Nord-lock washers for 14mm & 16mm motor axle, $9.50 (2 pr)

[shinyballs]

2 pairs including shipping with delivery confirmation within the U.S. I also ship overseas, feel free to PM me for shipping quotes, or any other questions.
$3 for each additional pair, payments will be by paypal.

As discussed here - viewtopic.php?f=7&t=22585&start=0
Each hub motor uses 2 pairs. The following prices are based on this configuration:
4 pairs = $15.50
6 pairs = $21.50
8 pairs = $27.50
10 pairs = $33.50

Steel(Through hardened), Delta Protect Finish, Thickness Tolerance +/- 0.01", Rockwell Hardness Min. 46 HRC, Meets/Exceeds DIN 25201

14mm: For Bolt Sizes (14mm)9/16", Inside Dia. 0.600", Outside Dia. 0.910", Thickness 0.130"
16mm: For Bolt Sizes (16mm)5/8" , Inside Dia. 0.670", Outside Dia. 1", Thickness 0.130"

Assembly instructions.jpg (123.96 KiB) Viewed 2611 times

lubrication.jpg (134.84 KiB) Viewed 2611 times

Torque guidelines.jpg (147.77 KiB) Viewed 2611 times

Reference:
http://www.nord-lock.com



Nord-Lock Demonstration Video

[Stevil_Knevil]

In addition to - or replacing -- torque arm?!

[oldpiper]

In addition to - or replacing -- torque arm?!

In addition to. The washers should do an excellent job of preventing your axle from getting loose on the dropout, but it won't prevent the dropout from getting torn off if there's too much torque applied to it.

Cameron

[RallySTX]

PM sent

[RallySTX]

Got em, today! Thanks E.
Brian L.

[chroot]

Is this Nord-lock for 9C axle? I forgot what size on the 9C axle.

[shinyballs]

Your welcome Brian. Glad you received it.

Is this Nord-lock for 9C axle? I forgot what size on the 9C axle.

Yes

[RallySTX]

Absolutely, Iinstalled one each on both of my 9C hubs last night, and they fit perfectly. They just aren't as wide of a washer as you might expect. They will hide under the nuts on your axle, compared to the standard washer that will stick out. Your only concern would be if you have enough axle length to acomodate the added thickness, as they are quite thick. But that's to be expected, if you watch the video, you will understand why. Enclosed are pics of my bikes with Nordlocks under the axle nuts.





Hope that helps.
Brian L.

[shinyballs]

bump

Here shown mounted on a 9c axle with an E-bikekit safety washer,rear rack and torque arm.

[liveforphysics]

Nordlocks absolutely 100% rock the pants off any other solution to keeping tension on a fastener (short of welding it).

You're a good man for buying a box of them and distributing a normally costly thing to acquire at a reasonable price.

Some ebike reseller should start including them with kits. It would simply end all the nuts loosening related failures.

[shinyballs]

you are more(100X)
Nords are a must have or the Disc-Lock nut where the locking part is already embedded on the nut, although the former has a higher Rockwell hardness.

Nordlocks absolutely 100% rock the pants off any other solution to keeping tension on a fastener (short of welding it).

You're a good man for buying a box of them and distributing a normally costly thing to acquire at a reasonable price.

Some ebike reseller should start including them with kits. It would simply end all the nuts loosening related failures.

[Alan B]

I put a set of Nord-Locks on my 9C 6x10 build awhile back. With the aluminum dropouts and dual torque arms I really don't want anything getting loose! Recently I needed to remove them for some work. As I removed them I could feel the tension increase, then drop after the ramp was passed, exactly as they are designed to work. They work really well when applied correctly. Highly Recommended!

[chroot]

One more question, Do I need 4 - pairs of Nord-Lock on left and right side?, or Do I need just 1 of pair on right side (Freewheel side axle)? and Let me know.

Give me your paypal email address, I need few couple of pairs for my 9C and xlyte HS3540 motors.

[Alan B]

The normal configuration is a pair per nut.

[shinyballs]

pm sent. Thanks Alan B.
Edited top post to show prices based on this configs.

[shinyballs]

the usual bump.

[bionx 1954]

Hi I got my Nord Locks a few days ago from Emmanuel (great guy to deal with) about a week from ordering them

I have a 9C 2807 front 26 in running on 72V Lyens sensorless controller that can peak at about 2500 watts. I do run dual torque arms, but the axle nuts still come loose some what. I installed 2 pairs (one per side) they are about 3/16 in. each set. They have a serrated side and a step/cam side, as you tighten them you can feel the ratchet effect, and when removed a loud pop when the pressure is released.


Well I went for a 2 day ride of 100 miles and check the nut periodcally and they STAYED TIGHT with no movement.



I think for a mere $ 7.50 for 2 pair that is CHEAP INSURANCE AND PEACE OF MIND. Thank Emmanuel Neil

[liveforphysics]

Nord-lock's are the absolute best in fastener locking technology. Money well spent for all those who bought them.

[psycholist]

PM sent

[rui_fujino]

does anyone here know if it fits with HS3540 well or not? cos i believe HS are 12mm instead of 14mm?

thanks

[nicobie]

does anyone here know if it fits with HS3540 well or not? cos i believe HS are 12mm instead of 14mm?

thanks

Yea, they fit fine.

I need a second set for a new bike, are these still available?

[ohzee]

Yea I was not aware of these either would like a couple pairs if available.

[captain387]

Do you ship to Canada or is there someone else who is supplying the northern country?

[999zip999]

I notice my axle showed some wear with my steel frame. Will these fit bmc hub axle ? Plus what's a good torque arm ? Thanks.

[shinyballs]

Thank you for clarifying, PM sent.

does anyone here know if it fits with HS3540 well or not? cos i believe HS are 12mm instead of 14mm?

thanks

Yea, they fit fine.

I need a second set for a new bike, are these still available?