Recent content by Hexa

The complete lenght with the case is 38 cm :wink:

Hello Guys, i´ve made an nice Case for the Flatpack 2 wich uses the original holes of the Case. The Case and all other infos can be found on Thingiverse.com. Here is the link to the file: http://www.thingiverse.com/thing:2243834 If someone is interrested getting it printed by me please write...

On Thingiverse there is a server problem os that you can´t see all my designs. So here are the direct Links to the parts : Rearlight (backlight): http://www.thingiverse.com/thing:2191708 Rearshock Cover: http://www.thingiverse.com/thing:2195822 LED Light Clamp...

What the F***! :shock: i think it is a server failure of thingiverse.com. Here are the Direct links to the Files: Rearlight (backlight): http://www.thingiverse.com/thing:2191708 Rearshock Cover: http://www.thingiverse.com/thing:2195822 LED Light Clamp...

The Indicators are from ebay :D If you want the Sideplates and the backlight here are the prices: Backlight (only printed part) 5€ Backlight with Led´s 7,50€ Backlight complete ready for use (including soldering, Cable etc...) 15€ Big Sideplate with all Screws and nuts...

Hello Guys, i´ve designed some really nice 3D Files for my Vector Frame. All files i´ve created can be found on my Thingiverse page. Just follow the link and you can discover a lot of nice Files including a lot of pictures, manuals etc.... http://www.thingiverse.com/H3x4/designs If someone...

Hello Guys, i´ve designed some really nice 3D Files for my Vector Frame. I know that there are a lot of Frames on the market with the same mechanical Dimensions so i think these parts fit on a lot of frames :D All files i´ve created can be found on my Thingiverse page. Just follow the link...

Thanks for the Info. I also get some Infos from Allex. He said that you have to take an real SD Card and not an Micro SD with an SD Adapter.

Hello Guys, had anybody of you the following Problem: I wanted to update my MAX-E Firmware so i prepared the SD Card, openend the Display and plugged the SD-Card in. When i then power up my Controller the backlight of the screen goes on on but the display stays blank. Is the SD card not...

Have you set all Settings in the "charge Settings" right? Today i got an Error at Charging too! My Max-e charged my 20S Lipo Battery with an 12V 500W PSU at 30A. Until 81V the charging process worked great. As i looked after the Bike some time later i noticed that the Controller was in Protect...

Using the Hall negative is absolutely okay. I am using this Connection too and i have absolutely no Problems. I recently bought an Max-e and it nearly works perfect! There are only 2 issues that i don´t understand. I am using an QS205 Motor with an MAX-E. When i start an Autodetect process the...

Thanks but it is my cellar ;) I did the throttle calibration and the upper and lower limits are just fine. An indicator for that is that in SLESS Mode the Motor runs just fine. I just tried every Hall Angle in the Menu but no configuration let the motor spin. The motor just twitch one time...

No i connected the Minus of the three Hall sensors to Battery Minus, the Minus of my Lipo Battery Pack because i have a bad connection of 13k Ohm on the Halls Connector of the Controller. I made an Video that shows the failure. Just follow my Dropbox Link...

I already checked the Halls And every Sensor changes between 0V and 5V so the three sensors are working perfect. Also i have no Pas installed. I will make an Video to show you the problem. There are no Shorts or anything else. So is the Colour wiring of the Cro diffferent than the wiring...

Help!!! I just connected my Cromotor v2 to my Adaptto Mini-e Cotroller. I directly got the !Halls! Error when powering up my Controller. So i did a bit of measuring around. I noticed that i got 13K Ohm Resistance between Battery Minus and the Halls Connector minus. Also i measured minus from USB...