Hi Elinx,
>>
I meant all the values that are in the screen above that I attached… TZDZ2 Assistance Settings… and the values on the screen for TAB Basic settings, and the values for Advanced settings.
I want to take my time reading through the Configuration Manual, and then enter all the...
I tried to download SDCC but have BitDefender anti virus running.
I am downloading from https://deac-fra.dl.sourceforge.net/project/sdcc/sdcc-win64/4.2.0/sdcc-4.2.0-x64-setup.exe
BitDefender prevents this from downloading.
Is this a legit source for SDCC and if so, I assume that I should...
Hi,
Does anyone have available an Excel Spreadsheet of all the Calibration settings for the OpenSource from Mbrusa ?
I have attached an image of one of the screens, I am hoping that someone has already created an Excel spreadsheet of.
I have searched this thread for it, but can't find a...
Thanks again guys,
It sounds like the Arduino is beyond my skills.
Letting go the throttle, shifting, and applying the throttle again makes sense.
Presumably stopping pedaling will also shut off the motor quickly.
So I will leave out fitting the gear sensor and see how I get on with that...
Hi Tomjasz,
Sorry to read about your experience with the shift sensor.
I might try the quick tap on the brakes to see if this could work changing gears while using a throttle. I am waiting
for the motor and all the parts to arrive before I arrange for the motor to be fitted to the bicycle.
Thanks Blacklite,
I am a complete beginner so don’t know anything about these things.
Does fitting the Arduino component shorten the length of time the signal comes from the gear shift sensor?
As the signal will be ‘interpreted’ as a brake sensor, would the motor still not turn off for over 2...
Can the OpenSource programming can allow the motor to be cut-off for a shorter length of time
while the gears are being changed?
I am guessing not, as this gear change sensor will be wired in as a brake sensor?
Hi V85,
Thanks for letting me know about those shorter batteries!
I have never bought one of these before.
Is it difficult to source the Samsung batteries to put into this case?
And to get the right connection for the Tongsheng TSDZ motor?
Best Wishes,
Dave
Hi,
I am looking for a 48V battery to fit a Giant Escape 0 small-size bicycle.
I measured the available space, and I am looking for a battery that is preferably 300mm (or less) in length, and 110mm (or less) in height.
Ideally with Samsung batteries inside.
Ideally with high ah… possibly...
Thanks Beemac,
So it sounds like I will route the cables for the hydraulic rear brake and the gear shifter outside the downtube and just hold
them in place with cable ties.
Fingers crossed the downtube won't get in the way where it beets the bb.
I will post a reply after the motor arrives and...
Hi,
Can anybody advise whether the current location of the cables under the bottom bracket in the photo, will cause a problem when installing a Tongsheng mid-drive TSDZ motor?
The bike is a Giant Escape 0.
The cables are for the hydraulic rear brake, and the gear shifter.
Is there some way...
Hi,
I am based in County Galway in Ireland.
I am planning to buy a TSDZ2 750 watt 48 volt mid drive motor to install on a Giant Escape 0 hybrid bike.
I am hoping to find someone in Ireland who has done this before, and who has experience programming it with the Open Source Software.
If you...
Hi,
I am based in County Galway in Ireland.
I am planning to buy a TSDZ2 750 watt 48 volt mid drive motor to install on a Giant Escape 0 hybrid bike.
I am hoping to find someone in Ireland who has done this before, and who has experience programming it with the Open Source Software.
If you...
I know very little about this, but I have done a lot of research.
If anybody thinks the power from the Tongsheng is weak, please read about the OpenSource code that
can change the setting to improve the power.
https://github.com/OpenSourceEBike/TSDZ2_wiki/wiki
And for anybody who has not...