Recent content by thender

That makes sense about the regenbraking. The reason I thought it had something to do with regen braking is because grin did something when advancing from the phaserunner MT to the L10 V6 where they tied the throttle and ebrake together. I wasn't getting any movement when I flashed my old...

I don't have enough to answer your first question unfortunately. I don't have a way to tell RPM while on the bike. I know I am below the RPMs I used before since I have my field weakening amperage set way lower than before, and I am way below the power I have used before since I used to use this...

I replaced a dead phaserunner MT that I used with a cycle analyst on my Bafang BBSHD with a newer L10 v6 phaserunner. I would've used a direct replacement but the old MT is not for sale anymore. This wiring harness worked just fine after replacing the anderson connectors for the motor phase...

I was curious if anyone had recommendations for good circuit breakers for batteries? I noticed anything liquid resistant is usually fro 24/48v marine stuff. I have three 20S10P batteries running in parallel, all connected to this bridge rectifier...

I put 72v through mine with 40-50 amps on a regular basis, no modification. No need.

Hi, I have an ASI BAC800 that was programmed by ERT. It was waaaaay too aggressive - it would make this "ga-ga-ga" sound while starting and act like it wanted to rip the chain with every engagement. It sounded like an angry midget with a sledgehammer was bashing something rather than a motor...

Yeah, I tried every protocol down the line. I had a session with ASI and sent them my programming, they added options they thought would fix, no dice. I gave up.

I had a chat session with the good folk at ASI, but no luck. They think it is just a display not programmed for it. Strange since this display works with a BBSHD stock controller, but doesn't work with ASI's BAC855. Does anyone here have a display they use with the BAC855 they can confirm works?

Hi, I've tried using this controller with a 750c screen that it once came with(from Alan at ERT), and an 850c screen I bought just incase my 750c had went bad. Neither work, with a new controller. 1) I have connected the controller to the computer and used the bacdoor app to change parameters...

Yeah, I know those aren't correct - I am saying that I'd rather buy those and cut the wire off and re-terminate than wait a few weeks for HIGO since you can't buy them in the United States. But apparently you can - the amazon prime listing you showed me is invaluable - I'd rather have that since...

Thank you! I have another BAC855 here that I was going to use on a different build - where the serial connection works. People sell this specific controller pre-programmed with a display, so I imagine there are ways to make it work. I will try and dig that out of ASI support. I noticed that...

I have a BBSHD screen and I want to hook it up to an ASI BAC800 controller. I would like to stick with the original connector that was on the screen - so I need to find the alternate end. What is this connector called? I can't find the name anywhere. I attached a picture. I would love to use...

I can't get that to see a controller. Thank you to the anonymous kind soul who sent it over. I do have a login to bacdoor, as I paid for another ASI evaluation kit. I thought I'd try using it to log into this BAC800 and change that setting. There is a parameter access code that is required...

I bought a battery from EM3EV. It had an issue with shipping where they would've been in the clear even if I filed a chargeback(which I never threatened to do, I am just saying that they would've been able to keep the money). They expressed me a 2nd one anyway. When the 1st was found I paid for...

This has standard 5v, ground, TX, and RX. If I open up the USB-Serial cable that comes with a Sabvoton SVMC72150 and change the connector so I can wire it up to the ASI BAC800 TX & RX pins, can I attach it to the ASI BAC800 and get it to work? Or is there more required? I am using the...