Search results

Date Relevance Most replies

  1. Ingo

    Cycle Analyst V3 preview and first beta release

    I wrote grin a long time ago. justin gave me a short answer and then he handed it over to an employee. this employee said it was my controller... my controller has been running trouble-free for several years and I haven't changed anything.
  2. Ingo

    Cycle Analyst V3 preview and first beta release

    now i have create a new setting + resetting the CA to standart... still no change. the speed limiting is very poor, overshoot, hesitate. not good someone have an idear ? grin ?
  3. Ingo

    Cycle Analyst V3 preview and first beta release

    thanks for the answer. usually justin always writes that when you have to create a completely new setup file. this time it went like this. I will try to reset the app completely and create a new setup file. Yes, I have already written to grin but they have no solution for this.
  4. Ingo

    Cycle Analyst V3 preview and first beta release

    Hi everybody, since version 3-2b3 i have some problems with the PID control to my CA. with the previous version 3-15b3 there were no problems with my settings. I attached the files. With the previous version and these settings (dsgain=0 , PSgain = 4V/sec , Isgain = 150) the speed limit worked...
  5. Ingo

    Cycle Analyst V3 preview and first beta release

    hi all, there is a new version 3-15b3 out with the fixed issues i have .
  6. Ingo

    Cycle Analyst V3 preview and first beta release

    there you must ask grintech
  7. Ingo

    Cycle Analyst V3 preview and first beta release

    yes accept the bugs its a good firmware
  8. Ingo

    Cycle Analyst V3 preview and first beta release

    Section titles show the feature/problem tracking number and description. Release: 3.15b1 2021-03-18 NOTE: This firmware is instrumented to detect illegal writes to any setting in EEPROM. The CA intercepts these errors before...
  9. Ingo

    Cycle Analyst V3 preview and first beta release

    hi all, i noticed some bugs at the new firmware 3.15b1 the present name does not match with the name in software. (showes different between CA and software) e.g. pdl ast = legal some bugs in calculated %Regen. show me 987% (should be about 1%) someone can help me here? regards ingo
  10. Ingo

    how to program a sevcon gen4

    can you give me the dfc file for this motor ?
  11. Ingo

    how to program a sevcon gen4

    hi @darseygodwin thanks for your support and information. unfortunately my engine didn't last long. I think it was a winding failure in the winding. i now want to mount a EMRAX 208 LV inside my motorcycle. anyone has this combination with a gen4 size6?
  12. Ingo

    PMSM Emrax 188 LV 30kW + Controller?

    hi all, i like to buy a Emrax 208 LV and use it with sevcon gen4 size6 at 96v lifepo battery for max 30kw power. someone have a dfc file for this compination?
  13. Ingo

    how to program a sevcon gen4

    hi all, i fixed the problem . it was lowering the d axis current protortional gain
  14. Ingo

    how to program a sevcon gen4

    here the videos : https://www.youtube.com/watch?v=WVXwtAJ1Jks&feature=youtu.be https://www.youtube.com/watch?v=CKBS-9wWhZU&feature=youtu.be https://www.youtube.com/watch?v=3fZvcIV5f5w&feature=youtu.be
  15. Ingo

    how to program a sevcon gen4

    hi, i have now measured the sensor while the motor was running and the noise was there. there is no mutch elektrical noise, so i think the sensor and the wires are not the problem. when the motor speeds up sometimes the nois disapears. i will upload a youtube video where you can hear the...
  16. Ingo

    how to program a sevcon gen4

    @darseygodwin hi, i have only a killswitch (cut batttery in a half) my technikal inspector says this is ok. then i have a drive select switch and when you operate the brake then the throttle signal goes to 0V. the throttlesignal comes from my cycle analyst so there is no B- to throttle, only...
  17. Ingo

    how to program a sevcon gen4

    @darseygodwin hi, thanks for the report. yes i can make some pictures. with the first original me1304 motor i dont have this noise. i try the shield the encorder cable but doesent make any difference. then I moved the encoder cable differently (away from the phases). does not make a...
  18. Ingo

    how to program a sevcon gen4

    hi, here the photos
  19. Ingo

    how to program a sevcon gen4

    hi, you must connect motor, sensor, battery, throttle, and some switches to get the controller run.
  20. Ingo

    how to program a sevcon gen4

    hi, here some files
  21. Ingo

    how to program a sevcon gen4

    hi, i can only change to 90us. it makes no difference
  22. Ingo

    how to program a sevcon gen4

    hi, ok i will test it. thanks!
  23. Ingo

    how to program a sevcon gen4

    it look like the offset is changing when current is given to motor
  24. Ingo

    how to program a sevcon gen4

    hi all, I have another problem with my sevcon gen4 size6 and ME1302 motor. when i give a little throttle (current is low) the motor runs fine (with the wheel off the ground) but when i give more throttle (current is higher) the motor / controller beginns to make a squeak / whistling noise very...
  25. Ingo

    how to program a sevcon gen4

Back
Top