Search results

Date Relevance Most replies

  1. B

    Halled motor cogging on start up, what could be my issue?

    Thats what i thought, but i tried every combination of the phase wires multiple times with both motors and i could only get it to run smoothly in reverse so i swapped motors and eventually just ran with it. Swapping halls may be the answer but thats 5 wires and they are a lot smaller and more of...
  2. B

    Dragy 0-54mph, Mantis 10 pro, 96v with modded stock controller

    Not trying to thread jack but since i posted my story in these comments.... Update to my "build" with Mantis King GT guts in my mantis 10 pro. New controllers, throttle, display and hub board. I was able to achieve a 5.0 second 0 to 30 on a good day, best run ever and today I've been doing...
  3. B

    Halled motor cogging on start up, what could be my issue?

    I think you are right on all accounts from what i can see. Swapping the phases i can get it to rotate forward but it has a cogging issue every time, with both motors. I tried every possible combination of the 3 phase wires. This will be an issue because the rotor is on its intended side so not...
  4. B

    Halled motor cogging on start up, what could be my issue?

    This is a "new build" basically updated controllers and display/throttle swap that is 100% OEM for these motors on a different scooter frame. The cogging switched from the rear, to the front now when i swapped controllers, although i have 2 brand new rear motor controllers so i got to test both...
  5. B

    Halled motor cogging on start up, what could be my issue?

    Did this once already but tried again today and it transfered to the front motor instead of the rear..... But what gets me is that i have 2 brand new controllers and they are both not working but acting slightly different. One sems to cog a little more, the other seems to just full cut out and...
  6. B

    Halled motor cogging on start up, what could be my issue?

    Im stumped on what is exactly going on here. I have brand new controllers, swapped the rear motor with a new one and no change, figured i got a faulty controller as its happened before in the past, but nope its still having this issue. Im not sure where to go from here as this...
  7. B

    Halled motor cogging on start up, what could be my issue?

    I triple checked all connections, one of them was loose when I tried putting it back together but I crimped and re connected everything to make sure all connections were secure. I havent ran into any obvious over heating issues but only rode it like twice ao far. I hope the controller resolves...
  8. B

    Halled motor cogging on start up, what could be my issue?

    Do you think i am losing power from this issue, or is it likely still putting out full power when rolling and not cogging? Its a brand new controller/hub board setup on fairly new motors. Decided to just replace the motor as i got it cheap ($100) but turns out that did nothing. I will replace...
  9. B

    Halled motor cogging on start up, what could be my issue?

    Its a hub motor (scooter, sorry) and i get a strong cogging on start up as seen in video. No load, no cogging, Light throttle = less/no cogging. Soon as the motor is spinning the cogging is gone but i feel as though its not running perfectly as it has a slight hesitation from a roll on. What...
  10. B

    vsett 10+ project

    You need more voltage (new or more batteries) for increased top speed. More amps from a controller would help acceleration but not much for top end.
  11. B

    Dual hub motor E bike vs single motor mode, which is more efficient?

    Thanks for the information! Im surprised no one else chimed in here, it must be a lesser known topic. I can't find much on google but ill try a search on this forum!
  12. B

    Dual hub motor E bike vs single motor mode, which is more efficient?

    On a dual hub motor bike, i have two questions about efficiency. Is it "bad" to run ONE motor at a time (bad for the non running motor or controller) if so, why? Is it more efficient to run both hub motors vs one, or the opposite? Which will provide more range?
  13. B

    Parallel battery for extended range, is it safe?

    This seems like the best option, switch to the second battery via mechanical switch if needed. You may not be able to get the benefits of lower discharge rate/battery sag but at least it seems to be 100% safe for both batteries.
  14. B

    Parallel battery for extended range, is it safe?

    Long story short, Is it safe to run a different brand battery (both 18650 60v, newer packs, each have BMS in casing) in parallel for extended range? If so, is it possible to run just ONE pack when needed or both when range is necessary? I can think of how to wire it up but i just dont know if...
  15. B

    Dragy 0-54mph, Mantis 10 pro, 96v with modded stock controller

    I have the Mantis Pro "V2" with the "upgraded" motors which are identical to the Mantis King GT, im not sure which ones you have but the top speed alone, is due to the controllers and that's about it. The controllers are also halled sinewaves so that could be part of it as well im not sure. I...
  16. B

    Dragy 0-54mph, Mantis 10 pro, 96v with modded stock controller

    I guess i should have stated im not interested in gaining more top speed, so amps are my main concern. However, more amps will increase the top speed at least a few mph because of the power increase. The Mantis King GT does 43mph on flat ground vs the 37 ish of the old Mantis and they have the...
  17. B

    Dragy 0-54mph, Mantis 10 pro, 96v with modded stock controller

    I am tempted to run a couple 3s in parallel for inline to my main battery but i have a few things that are bothering me. Lack of internal space would make me seek external locations 3S battery would require a different charger or disconnecting and charging both the main battery AND lipo's. I...
  18. B

    Dragy 0-54mph, Mantis 10 pro, 96v with modded stock controller

    Wow, amazing work. I would love more power from my mantis but I'm not sure where to start. I have some lipo batteries on hand from my rc hobby but would it even be worth running a 3 or 4s lipo inline with everything else stock? It would be easier than pulling the controller apart and changing...
  19. B

    Mantis 10 Pro - Has anyone modified one to make it faster?

    Replacing the battery or adding an inline series external battery are the only ways I know of increasing voltage. If i were to get an external battery, would it need to match the same amperage as the internal battery? To avoid discharging or having more juice than the internal battery when it is...
  20. B

    Do these circuit boards look the same?

    They do dont they! im almost positive they are not working correctly though because i have it confirmed to be downstream of the motor connection which is where the axle meets the swingarm.
  21. B

    Kaabo Wolf King GT vs Jeep Grand Cherokee V6

    No clue, this was my buddies and i only got to do a couple runs with him! His main goal was to hit max speed (72mph) and thats mostly what we were out there for. Id be curious to see those 60ft times though maybe i can get him to run again
  22. B

    Dragy 0-54mph, Mantis 10 pro, 96v with modded stock controller

    Thats funny you say that because i was thinking about doing the same thing. I got my Mantis from Aliexpress for under 2k shipped, and we all know your service is out the window if something breaks on the scooter.... turns out i had a bad controller that would intermittently cut out after it...
  23. B

    Kaabo Wolf King GT vs Jeep Grand Cherokee V6

    Official GPS top speed was 72mph and 0 to 30 mph in 3.5 seconds. https://youtu.be/eU_A-Z_YiH8
  24. B

    FFR - Horizon motor swap

    I swapped the motor on one of my Fluid freeride Horizons with a T9/zero 9/apollo city motor and it's been great so far. Speed went from 22 to 29 on flat ground, up to 33 on a slight down hill with a lighter rider and the pneumatic tire gave it a lot more stability and braking power (one rear...
  25. B

    Mantis 10 Pro - Has anyone modified one to make it faster?

    I have Kaabo Mantis Pro 10 and i would love to modify it if there are known upgrades/parts to swap out on it. I am fairly inexperienced compared to some people here with impressive builds but i have worked on all my scooters and can make my way around, i just havent found anything that's...
Back
Top