Endless Sphere

Indigodee wrote: ↑

Aug 28 2020 2:43pm

Do you have any consoles left at all? I know it’s an old old thread but! On the off chance lol. Thanks. Dee

no, Sorry

for 36 spokes moto rim with angle for crossed spokes, bike rim for bigger nipples 30€ each plus shipping, according to your country new and unused, MXUS 3K motor was delaced when new black moo and bike are Aluminium, Chrome should be steel Moto 16" black, 17" chrome, both 1.6", inner ...

Selling some Falco motors stuff, see pics
Paid 120€ for the programing cable
various cables, throttles and connectors and sideplates, new and used

asking 50€ plus shipping according to your country. I'm in Austria

ASI BAC

Connect the programing cable and check what the software says
try to run it sensorless

Does anbody know which profile has to be used with the 24 fet 4115 EB624? I can find it just for 18fet max. Thanks

better to have somebody with a lathe. The axle and the thread have about 0,2 mm difference, which gets bigger and bigger with every acceleration. A thread is never that strong than a even metal. There are plenty of adapter for the BBSHD, you can use them. But the motor will be pressed to the adapter...

If you really THINK you know it, go drag race a BBSHD at 50A with your skinny wife on it (until the Nylon gear goes) against a strangled CYC running at 50 A when the whole point is it can handle mush more (like 90A peak BAC 800) If you want to fit he CYC to a heavy EEB frame or Vector or similar - ...

it is the 13S controller, which also runs with 14S
I don't have the 20S controller yet

finally I found some time for filming and editing:
https://youtu.be/YkjWWj9loX4

After a few improvemts in firmware and few testrides we compared it to the BBSHD with shut mod. Pretty impressive for his size and definetely more torque!

Grin is now offering a ready to go harness for the BBSHD
a have ordered a few and took a few pics how it works
for all interested in:
moderator removed this link- it did not contain what it claimed

BBS02 is already on the limit with 25A
the robust controller is useless, if your motor is too weak
go for a BBSHD

I had melted Anderson 45 phase connectors with the original 30A
I would suggest some other connectors, like 4 mm gold or also the MT60 for phase

I am about to pull the trigger on purchasing a CA and phaserunner and I will figure it out as I go. I assume I need the CA3-DPS rather than the CA3-DP? or can I use the speedo from the BBSHD unit somehow Go for the CA3-DPS. The speed signal goes into the controller and you remove the original contr...

you had to remove the Ludi pics?

Thanks, can you post you complete configuration file of the Phaserunner, please

Thank you for all the helpful info. About my previous display question: DPC14 is made by APT display, what about DPC18 made by Bafang? Is this really a problem of the display or the controller itself? The question is, if the display DPC14 shows a lower voltage using a voltage dropper resistor, than ...

Just to make a summary after reading everything twice. For a 50A mod replace the 2x 5 mOhms on the rear side of the PCB with 2x 3 mOhms (Width: 3.18 mm Length: 6.35 mm, Height: 0.35 mm). Power can be lowered in programming software, for example 24A = 40A Mouser WSLF25123L000FEA original display goes...

hi Allex, I bought 2 Adaptto Midi and both failed. The first one was sendet to Russia for warranty as you assumed. Waited more than 2 months and many emails. Had to pay for repair, even it was broken from beginning. Both the controller you sold had no warranty sticker on it, which is also a problem ...

would be nice Reinhard! And great work as always… what we also need is a proper setup than. If you could post your experience with settings would be great! I have got some basic info from Justin directly: there are two ways of tuning the PR to a mid drive like the BBSHD system. Either you look at th...

get a MXUS 3K 3T, which is better and cheaper
always a problem lacing a TC

would be nice to get a full setting list, since we can organize the parts by our self. Seems that ERT let wait his customers for months. And I know I'm not the only one to be interested… Thanks

How about posting all the used settings of Phaserunner and CA? Since I already have Phaserunner, CA and BBSHD… would be great. I think I'm not the only one. Thanks

Ciao Burner, una domanda per quanto riguarda l'asse 16mm dell motore. Come viene montata al motore? Atraverso chiavetta? dalla foto sul vostro sito non sno riuscito a capire. Faccio questa domanda per sapere se serve una pressa, o se e fattibile entrare con la ruota ja montata senza l'asse e poi en...