Search found 2057 matches

by E-HP
Apr 12 2021 6:56pm
Forum: EBike Troubleshooting
Topic: Accidental ebike newbie with controller and battery questions
Replies: 9
Views: 121

Re: Accidental ebike newbie with controller and battery questions

I've got an option to buy a new 36V10AH 250-350w Li-ion bottle cage battery for £100 ($130) which I might take up then. Seems like a good deal for UK prices. There are no good deals when it comes to batteries. Getting what you pay for is as good as it gets. However, there are plenty of bad deals. $...
by E-HP
Apr 11 2021 1:55am
Forum: EBike General Discussion
Topic: Tempted to lick my 50 volt battery
Replies: 39
Views: 646

Re: Tempted to lick my 50 volt battery

Hummina Shadeeba wrote:
Apr 10 2021 9:37pm
How safe is it? I mean what are my chances of death?
Maybe start with a different orifice just to play it safe. Then your tongue. :confused:
by E-HP
Apr 10 2021 1:31pm
Forum: EBike General Discussion
Topic: Tempted to lick my 50 volt battery
Replies: 39
Views: 646

Re: Tempted to lick my 50 volt battery

tastes like chicken...
by E-HP
Apr 10 2021 11:34am
Forum: EBike Troubleshooting
Topic: Hub motor axle slipping out of frame
Replies: 12
Views: 204

Re: Hub moto slipping out of frame

Kyleraee94 wrote:
Apr 10 2021 10:08am
i have torque arms and washers so all spacing is even but still slips out
Do you have washers both on the outside and inside of the dropout?

https://i1.wp.com/www.ebikeschool.com/w ... .jpg?w=640
by E-HP
Apr 08 2021 9:25pm
Forum: EBike General Discussion
Topic: Different power levels 8 pin 6 pin dispays.
Replies: 5
Views: 136

Re: Different power levels 8 pin 6 pin dispays.

Maybe , but the power level is confusing, you press the + - buttons to adjust power level , but that brings up the wheel circumfurance setting. How do you progress on to power level? Not sure, but what happens if you press the + - again, after getting to the wheel circumference settings? Either tha...
by E-HP
Apr 08 2021 9:38am
Forum: EBike General Discussion
Topic: Upgrade old battery or get new one?
Replies: 8
Views: 228

Re: Upgrade old battery or get new one?

You can probably get 17Ah from good cells, in a pack of that size. Unless you have the equipment to test cells and assemble the pack (spot welder, etc), then getting a new pack seems to make more sense, unless the bike uses a proprietary pack and interface with the bike controller.
by E-HP
Apr 08 2021 9:29am
Forum: EBike General Discussion
Topic: Different power levels 8 pin 6 pin dispays.
Replies: 5
Views: 136

Re: Different power levels 8 pin 6 pin dispays.

Have you messed with the "power select" parameter, and maybe have it set low on the VLCD6?

https://drive.google.com/file/d/1ZiNNZG ... wFUNB/view
by E-HP
Apr 07 2021 8:01pm
Forum: EBike Troubleshooting
Topic: Hello all, I'm new to forum and ebikes. Excuse my lack of Tech knowledge. Anyhow I got a new conversion on a
Replies: 8
Views: 213

Re: Hello all, I'm new to forum and ebikes. Excuse my lack of Tech knowledge. Anyhow I got a new conversion on a

Battery details output42V DC, 2.0A MAX RECHARGABLE BATT. CAPASITY 8 - 15AH BATT. TYPE SAN36V thanks for comments re Gear ratio. and lower max speed in level 1. I do feel that with optimum settings and smart contineus pedal assist I should be able to achieve a 100km range on flatish roads. regards S...
by E-HP
Apr 07 2021 4:08pm
Forum: EBike Troubleshooting
Topic: Dead controller
Replies: 3
Views: 162

Re: Dead controller

Do you have a link to the kit?
by E-HP
Apr 07 2021 1:29pm
Forum: EBike Troubleshooting
Topic: Electric scooter 1500W controller cold temperatures cutting out
Replies: 11
Views: 191

Re: Electric scooter 1500W controller cold temperatures cutting out

Hello, I've found the issue! FINALLY :p As it turns out, noone was right, it is not the controller nor the battery problem. I've had a chance to test my friend's LCD (with throttle), and it works flawlessly with his LCD (brand new one). Now I've started to troubleshoot the problem, and my hall effe...
by E-HP
Apr 07 2021 1:24pm
Forum: EBike Troubleshooting
Topic: Hello all, I'm new to forum and ebikes. Excuse my lack of Tech knowledge. Anyhow I got a new conversion on a
Replies: 8
Views: 213

Re: Hello all, I'm new to forum and ebikes. Excuse my lack of Tech knowledge. Anyhow I got a new conversion on a

sean02ie wrote:
Apr 06 2021 1:18pm
Battery 48volt Litium ion.
It might be helpful if you would provide the capacity of your battery rather than just the voltage.
by E-HP
Apr 07 2021 1:18pm
Forum: Bike Mechanical & Structural
Topic: Hub motor not working
Replies: 3
Views: 116

Re: Hub motor not working

Those windings near the bottom look fried.
by E-HP
Apr 03 2021 12:53pm
Forum: EBike General Discussion
Topic: New type of PAS. Is it faulty?
Replies: 14
Views: 688

Re: New type of PAS. Is it faulty?

The one you mentioned works fine. The one I had originally was made from a single piece of plastic or 2 pieces welded together :roll:. The KT-V12 is made from 2 distinctly separate pieces and therefore obviously turns like you would expect. That's good news, thanks for closing the loop. If you have...
by E-HP
Apr 03 2021 12:50pm
Forum: EBike General Discussion
Topic: Rear derailleur cable attachment lever arm hits hub motor gears 3-6 on six speed freewheel.
Replies: 12
Views: 275

Re: Rear derailleur cable attachment lever arm hits hub motor gears 3-6 on six speed freewheel.

Maybe just switch to a cheap regular derailleur instead of the clutched type. With a rear hub, you barely shift anyway.
by E-HP
Apr 02 2021 5:34pm
Forum: EBike Troubleshooting
Topic: Trouble shoot me!
Replies: 14
Views: 433

Re: Trouble shoot me!

E-hp, I unplugged the CA and tried it. It did the same exact thing: a 1/10 second surge and then nothing, with the controller still flashing those 4 LED flashes. Makes sense. Reading the manual, seems like the Cycle Analyst V2.23 shouldn't be a factor, unless it had a short, or was limiting throttl...
by E-HP
Mar 31 2021 9:12pm
Forum: EBike Troubleshooting
Topic: Trouble shoot me!
Replies: 14
Views: 433

Re: Trouble shoot me!

The system is set up so that one has to be pedaling and moving (wheel spinning) in order for the assist to come on. This curious thing happens: Nearly every time I switch on the power (CA lights up, red led shines on controller) and then pedal and spin the wheel, the motor clicks on for maybe 1/10t...
by E-HP
Mar 30 2021 9:58pm
Forum: EBike General Discussion
Topic: wiring up 3 switches
Replies: 23
Views: 411

Re: wiring up 3 switches

the xt60 is located in the triangle of the bike and I have 20awg wires running to the handlebars. I put a fuse on the positive before the xt60 and made a new wiring harness. I decided to keep everything in the triangle because I already have long cables running from the accessories and plus the rea...
by E-HP
Mar 30 2021 3:55am
Forum: EBike Technical
Topic: Bike has full charge and won’t spin tire
Replies: 13
Views: 265

Re: Bike has full charge and won’t spin tire

might be a wiring problem.
by E-HP
Mar 28 2021 10:15pm
Forum: EBike General Discussion
Topic: Walmart Hyper e-ride: Controller Swap Suggestions
Replies: 21
Views: 1157

Re: Walmart Hyper e-ride: Controller Swap Suggestions

Phaserunner will easily fit in the space, works with voltages from 24V to 72V, and paired with a Cycle Analyst 3, you'll have plenty of upgrade potential/options. You can set the current limits so you don't kill your stock battery right away, but ready for upgrading to likely any level that you'll ...
by E-HP
Mar 28 2021 11:49am
Forum: EBike Technical
Topic: Which throttle wire is which
Replies: 3
Views: 155

Re: Which throttle wire is which

You should be able to find your answers here, since it contains all you'd want to know about hall sensor throttles
https://electricbike.com/forum/forum/ki ... dification
by E-HP
Mar 28 2021 9:53am
Forum: EBike Troubleshooting
Topic: New guy with baserunner 'Current scaling' fault
Replies: 9
Views: 183

Re: New guy with baserunner 'Current scaling' fault

Thanks for that tip, but I cannot find it anywhere. Firstly, it is hard to know what is the 'last screen' and I could not find any option to restore. I see on the screen shots in this thread, a button that says "load default parameters". Not sure if that's it. https://endless-sphere.com/f...
by E-HP
Mar 27 2021 11:35pm
Forum: EBike Troubleshooting
Topic: New guy with baserunner 'Current scaling' fault
Replies: 9
Views: 183

Re: New guy with baserunner 'Current scaling' fault

I don't have one, but Page 9 of the manual says:
"Finally, the last screen gives you an option to restore all other Phaserunner settings to their default values."
by E-HP
Mar 27 2021 4:49pm
Forum: EBike Troubleshooting
Topic: New guy with baserunner 'Current scaling' fault
Replies: 9
Views: 183

Re: New guy with baserunner 'Current scaling' fault

CazBilly wrote:
Mar 26 2021 2:26pm
So then, I reset the CA3 to defaults but no luck. Still Current Scaling Fault
I believe resetting the CA3 wouldn't make a difference, since you made the changes in your baserunner software. Did you try resetting the controller software (restore)?
by E-HP
Mar 27 2021 2:20pm
Forum: EBike General Discussion
Topic: wiring up 3 switches
Replies: 23
Views: 411

Re: wiring up 3 switches

Not sure where the XT60 is located, but I'd advise minimizing the number of battery voltage wires running to the handlebars, especially if you aren't fusing. In other words, locate the XT60 at the bars and branch out from there. You can add a fuse where it branches from the XT90 to protect the circu...
by E-HP
Mar 27 2021 1:30pm
Forum: EBike Troubleshooting
Topic: New guy with baserunner 'Current scaling' fault
Replies: 9
Views: 183

Re: New guy with baserunner 'Current scaling' fault

CazBilly wrote:
Mar 26 2021 2:26pm
... and I turned down the motorpower to 550w as this is an basically unknown hub motor (300w 36v altho now 48v).
Now I have a fault: Faults2[1]: Current Scaling
I don't see a setting called motorpower in the manuals. Where did you see this?