Sticky thread index for "Motor Technology"

Status
Not open for further replies.

spinningmagnets

Moderator
Staff member
Joined
Dec 21, 2007
Messages
12,952
Location
Ft Riley, NE Kansas
Please be patient as this information storage will be organized over time. Any moderator may feel free to unlock and expand/re-arrange/improve as you see fit...

RUST: DIY Hub Motor Repair & Restoration
https://endless-sphere.com/forums/viewtopic.php?t=34135

Lebowski DIY axial flux motor
https://endless-sphere.com/forums/viewtopic.php?f=30&t=46476

"Motor PICTURE links, disassembled, hub and non-hub"
https://endless-sphere.com/forums/viewtopic.php?f=16&t=54935

"How to Determine the Wiring for a Brushless Motor" (Fechter, cross-post from tech reference section)
https://endless-sphere.com/forums/viewtopic.php?f=16&t=3484

pics of the insides of geared-hub clutches, MAC and BPM
https://endless-sphere.com/forums/viewtopic.php?f=12&t=88092

"Re-wind of a turnigy 80/100 (Now-tutorial w/Video)" (Thud, 17 pages)
https://endless-sphere.com/forums/viewtopic.php?f=30&t=20618

"Adding hall sensors to outrunners" (Burtie, 16 pages)
https://endless-sphere.com/forums/viewtopic.php?f=30&t=15686

"Optical sensors for commutation -Working" Burtie
https://endless-sphere.com/forums/viewtopic.php?t=28966

"mounting hall sensors to R/C brushless motors" (georgeycc, 11 pages)
https://endless-sphere.com/forums/viewtopic.php?f=30&t=9061

DIY shaft encoder, 3 Halls, 8 magnets, 3D-printed holder
https://endless-sphere.com/forums/viewtopic.php?f=12&t=93048&start=25#p1416679

"Timing Adjustment Tool" (Burtie, 18 pages)
https://endless-sphere.com/forums/viewtopic.php?f=2&t=19054

"Optical sensors for commutation -Working" (Burtie, 4 pages)
https://endless-sphere.com/forums/viewtopic.php?f=2&t=28966

"Adding burtie internal optical sensors to Astro 3210" (http://www.recumbents.com, one page)
https://endless-sphere.com/forums/viewtopic.php?f=28&t=39035

"ES Motor Project?" (Miles, 8 pages)
https://endless-sphere.com/forums/viewtopic.php?f=30&t=40092

"DIY 10awg phase leads through axle in 9C hubmotor." (liveforphysics, 5 pages)
https://endless-sphere.com/forums/viewtopic.php?f=2&t=14580

"Building a DIY triple stator axial flux motor" (Lebowski, 8 pages)
https://endless-sphere.com/forums/viewtopic.php?f=30&t=46476
 
"Ideas for dynos"
https://endless-sphere.com/forums/viewtopic.php?f=30&t=45869

"Throttle control modes"
https://endless-sphere.com/forums/viewtopic.php?f=30&t=78882

"Partial throttle and motor efficiency"
https://endless-sphere.com/forums/viewtopic.php?f=30&t=79229

"Battery amps Vs phase amps/ratio?"
https://endless-sphere.com/forums/viewtopic.php?f=14&t=82510
 
CONTROLLER LINKS

"How to determine the wiring for a brushless motor"
http://endless-sphere.com/forums/viewtopic.php?f=16&t=3484

"Lebowski's motor controller IC, schematic and setup manual" (Lebowski, 48 pages)
[plus index in first post, to all Lebowski threads]
https://endless-sphere.com/forums/viewtopic.php?f=30&t=36602

Sensorless motor control from a standstill (Lebowski)
https://endless-sphere.com/forums/viewtopic.php?f=30&t=94865

"SiliXcon FOC Controllers, small, powerful and many features" (madin88, one page)
https://endless-sphere.com/forums/viewtopic.php?f=30&t=98246

xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx


VESC based DIY controller links

"VESC-controller: Axiom hardware released!" (from marcos, 11 pages)
https://endless-sphere.com/forums/viewtopic.php?f=30&t=89056&sid=64159ea471b0faf1b02bd40703c7fa79

"BESC - beefed up VESC motor controller for high power ebikes" (galp, 3 pages)
https://endless-sphere.com/forums/viewtopic.php?f=30&t=97765

"Serious FOCer (84V VESC 6 based controller)" (shaman, 3 pages)
https://endless-sphere.com/forums/viewtopic.php?f=30&t=99152
 
Status
Not open for further replies.
Back
Top