• Howdy! we're looking for donations to finish custom knowledgebase software for this forum.
    Please see: Funding drive thread

Recent content by Blik86

  1. B

    S-LCD to S12S controller communication protocol hacked

    I won't say for all cases, but from what I was able to analyze, my CRC works without a multiplier. Most compensate with a multiplier for the presence of B0, B12 in their formula.
  2. B

    S-LCD to S12S controller communication protocol hacked

    Can you test the CRC I provided? (Without additional multipliers)
  3. B

    S-LCD to S12S controller communication protocol hacked

    Is the CRC I suggested not working? LCD>controller CRC = (xor B1,B2,B3,B4,B6,B7,B8,B9,B10,B11) controller>LCD CRC = (xor B1,B2,B3,B4,B5,B7,B8,B9,B10,B11)
  4. B

    S-LCD to S12S controller communication protocol hacked

    LCD>controller CRC = (xor B1,B2,B3,B4,B6,B7,B8,B9,B10,B11) controller>LCD CRC = (xor B1,B2,B3,B4,B5,B7,B8,B9,B10,B11)
  5. B

    S-LCD to S12S controller communication protocol hacked

    Correct jumper.
  6. B

    LCD8H for Rad Mini battery shows empty and bike not working

    Check that PAS is not "0". Try to activate "6KM / H power assistant push function" Try turning on the controller without a display. (A jumper in the connector). Check the pins in the display connector.
  7. B

    KT motor controllers -- Flexible OpenSource firmware for BMSBattery S/Kunteng KT motor controllers (0.25kW up to 5kW)

    Measured Tektronix A622, current in green or battery (13s) wire. The voltage is about 50-52V. I loaded the wheel with a disc brake, in time it is a couple of seconds and the controller turns off the motor (8fan bpm 10t). Pictures for the initially locked wheel and rotating with the subsequent...
  8. B

    KT motor controllers -- Flexible OpenSource firmware for BMSBattery S/Kunteng KT motor controllers (0.25kW up to 5kW)

    Perhaps in the original, it can give out more than 70-80A, but it will surely get hot even from lower currents. C5, but I didn't watch it. I don't understand the simulator. In my understanding, there are 3 phases in the motor .... if you count the rms, then for 3 phases with 80A amplitude...
  9. B

    KT motor controllers -- Flexible OpenSource firmware for BMSBattery S/Kunteng KT motor controllers (0.25kW up to 5kW)

    I had a phase current amplitude of 70-80A. https://endless-sphere.com/forums/viewtopic.php?f=30&t=87870&p=1426630#p1426630
  10. B

    Kt bluetooth controler (48v/500w) progamation information ?

    You need to read the kt-lcd3 manual or from another kt-lcd.
  11. B

    KT motor controllers -- Flexible OpenSource firmware for BMSBattery S/Kunteng KT motor controllers (0.25kW up to 5kW)

    Hello. Can the "wheelsize" value in the KT LCD protocol be calculated (does it mean something)? Or just decrypt according to the table?
  12. B

    S-LCD to S12S controller communication protocol hacked

    lcd8 manual: "L Parameter Setting 1. L1 parameters are applicable to the automatic under-voltage controller. The default of the factory is 0. 1.1 When L1=0, the automatic under-voltage controller can automatically select the under-voltage value according to the battery voltage. 1.2 When L1=1...
  13. B

    S-LCD to S12S controller communication protocol hacked

    CRC = (xor B1,B2,B3,B4,B6,B7,B8,B9,B10,B11)
  14. B

    S-LCD to S12S controller communication protocol hacked

    KT LCD6 protocol
  15. B

    KT motor controllers -- Flexible OpenSource firmware for BMSBattery S/Kunteng KT motor controllers (0.25kW up to 5kW)

    Hi How to check supports stock controller sensor temperature of the motor? Perhaps you have a stock controller circuit supporting a motor temperature sensor?
See more
Back
Top