Recent content by BSATOM

People! Posting negative things about others posts, with zero reference or proof of your negative statement is an inferior trait. My bike hauls ass, is tight in the corners, and rides very good. Just another negatively oriented comment with zero basis in reality. I just looked on Ebay and there...

Late 1990s GT LTS1 LTS2 LTS3 frames have a full front triangle for a battery box. They came in 4 sizes. A 14.5, a 16, an 18, and a 20". This refers to the seat post length. The 20 inch long seat post version is best because it has the largest triangle up front. I really like the "4 link" rear...

It only gets warm, not even hot. It is directly in front of my rear tire, so it is basically fan cooled. Also. It seems that only the 72v and higher versions are guaranteed to have the 100v 330w FETs I listed in the first post of this thread. Lower voltage versions seem to have the 75V FETs. I...

People are way off in their amperage ratings. I have ran 90 amps through my 15 FET controller daily with videos to prove it. They are the China 100v FETs I mentioned in my first post, and are rated for less power and with a higher on resistance than a 4110. I am powering a MXUS 4t with 20AH of...

Keep watching. I have 3 here that I got all this summer for the opening bid. Right now there are none up, but they have this here better controller with 18 FETS for $35 delivered. Here ya go...

Well, this controller handles 6400 watt intermittent and barely gets warm. I put a 100 amp breaker and pulled 90 amps for over 2 seconds so far. I call this a winner for $23.99 delivered from China within 3 weeks. No better deal that I can find.

Well it looks like you bought a well reviewed iron. That can solder sheet metal too. To the spot welder guy trolling a 18650 soldering thread... Nothing happens to the chemicals in 18650 cells when soldered properly. You can suggest and imply that there is unseen internal chemical damage all...

Here is a link to the controller thread. https://endless-sphere.com/forums/viewtopic.php?f=2&t=71128

If you read my post, I say that I use my d550 for heavy soldering like 18650 packs, and the station for general bench soldering. I did not imply that the Hexacon is for soldering 18650 packs power connections. Nor did I imply that the Portasol is to be used for 18650 packs. I included the...

I bought one and used it on my friends trike I built for him. The controller comes with the jumper plug included to use without an LCD. To turn on and set regen braking, to set the number of motor magnet poles, to set PAS assist, and several other important parameters, the LCD is needed. It...

That looks like this Hallomotor/Conhismotor unit. Correct current as 13.88 amps at 36v is 500w. It can be used fine without an LCD. You have to jump two wires as pictured. http://www.hallomotor.com/36v-500w-brushless-dc-sine-wave-ebike-controller-regenerative-function.html

Here is what I use to build 18650 packs. I use it to solder many other heavy connections on my Ebike. This is the lowest price on Ebay for one of these right now. The second link is the iron I use. I like my old Hexacon station. That is for all general duty bench soldering. I also have an old...

You do not "need" a spot welder, as I have soldered all my packs with a Weller D550. You also need thin wires and xh connectors for battery balancing leads. You will need Gorilla/duct tape and heat shrink. If I am making an odd shaped pack to fit in a triangle etc, I use a hot glue gun to stack...

Well I personally would be getting some XT90s along with an anti spark XT90S, or at least slide the Andersons together into pos/neg pairs. But if your personality is one of needing drama like you seem to indicate, then use all black wires and heat shrink(sarcasm). Anderson 45s at 150v huh? Must...

I am on board for the in the field FF testing. I have a new MXUS 4t that I have not used ATF in yet, but have beefed the wires. I am waiting on a 100a breaker so I can hit 7000w peak. I will watch for the post on how you will distribute the FF syringes. I suppose via Paypal. I am still curious...