Recent content by Dartman

I will refine a little more. Firmware is 3.2b3. If I select pass through or torque (A) mode for throttle, I got huge power burst kick everytime I start to pedal, doesn't matter if pas up ramp is 0.5V/s or 10V/s. This burst last maybe half second. With Power (W) throttle mode I get sophisticated...

Question to Justin, or someone else who have facts. :) What is fastest PAS ramp up value? I asking because I would like fastest response with Erider. I feel too much lag with 10V/sec. For example if I need to lighten the front end to cross the obstacle, assist reacts far too slowly. I raised...

When I open new 3.14 setup file in CA suite, Absolute Max Current Limit is 99.99A by default. Thats not enough for all, but you can manually enter 200A. That's why I asked How much is default Absolute Max Current Limit in 3.2b1

Ah ok, I see your issue. Those Start Trq and Thrsh Trq settings are for starting thresholds, but I assume when torque Nm goes under Thrsh Trq assist should stop, if not I see issue there which need attention. I haven't tried that or notice it as I drive hub motor. You should definitely get gear...

What I like to know... Justin or or someone else! (8) 8235 - (New) Wheel Torque Sensor PAS Option This change affects the eeprom configuration with the addition of new parameters and removal of the 'Absolute Max Current Limit' OEM setting. Firmware updates will set these...

If you want torque assist from dead start (without crank rotation): This setting uses two parameters to control behavior. PAS->Start Trq is the threshold torque that must be applied to the cranks in order to have torque assist from a dead start when the vehicle is stopped...

I updated firmware from 3.14 to 3.2b1. How do get speedo meter working? I tried 3.15b3 when it came and speedo didn't work, so I went back to 3.14. And yes, I know all settings and how those need to be, as I have using CA since 2013. I assume this change cause it? So how I get speepo working...

Where can I find firmware relese notes online? Link please.

Which channels Grin developers read? I sent email to Grin support like a month ago about power surge issue, no response what so ever. Feels like CA3 is yesterdays news and they not care anymore, electrifying wheelbarrows is more interesting.

I also confirm spontaneous power surges with ERider T9 and 3.15b3 firmware. When pedaling stops for half second, I get power surges when start pedaling again. Over one second pauses not cause power surges. When set PAS ramp up as low as 0.5V/s it will tame power surges, but also increase...

New controller housing size? Why wires coming out from both ends?

Did I bricked my CA3? Couple years ago I had boot issue, which fix it self some how. Now boot issue came back and CA boot successfully one of third boot. I decide to try old boot fix trick, I flashed CA3_BootFix_V01.hex and I select option 2. Now CA not boot any more, only back light come on :(...

I really like this Ebike Analyzer app, looks very stylish and works flawlessly with BlueSMiRF Silver BT-adapter. I hope to see updates and upgrades in the future!

I noticed weird issue after updating CA3-1b13_Conventional firmware. When I power on bike and twist throttle first time and let go, motor keeps running two seconds. Even if I try to slow motor with gently braking, it pulls about 50 watts power. This happen only once after power is turned on...

Hi, I like to share that I have CA v3 boot issue too, what few other has described here. I have Lyen's 12 x 4110 MOSFET Extreme Modder Controller and when I turn power on from controllers Ignition wire, mostly I got only CA's back light at first try, second attempt usully is successful. Strange...