Recent content by ijr9005

  1. I

    preset 7 s866 display magnet number

    my new to me brainpower controller with s866 lcd display has arrived and im very happyy with it, im using it on a lf-h04 geared hub, option 7, number of magnets, any body know the answer? seems for a geared hub its number of magnets multiplyed by gear ratio or something. will the self learn...
  2. I

    when everything is new and it still wont go

    retested the spare motor and its ok, put new hall sensors in throtlles, looking like second controller was faulty from new
  3. I

    when everything is new and it still wont go

    tester arrived today, tried putting the old controller back on, seems it was letting by 42volts into the control wiring, so throttle hall sensor and hub hall sensors in the spare hub have blown https://youtu.be/vTdzF8Y9_GE
  4. I

    when everything is new and it still wont go

    motor turns without any throttle when self study wires are connected, a new voilamarrt kit is 195.99, replacement parts have cost 145 and hub need lashiing to the rim so add another 30 is 175
  5. I

    when everything is new and it still wont go

    so when EVERYTHING has been replaced, and iit still wont go[/youtube], is it time to cut your losses, send the whole lot off to be recycled and accept that 2000 miles from a kit is pretty good value for money, $195.99 divided by 2000 is 10p a mile https://youtu.be/QEFZ-low5Fg
  6. I

    when everything is new and it still wont go

    power loss,rough running
  7. I

    when everything is new and it still wont go

    so when EVERYTHING has been replaced, and iit still wont go, is it time to cut your losses, send the whole lot off to be recycled and accept that 2000 miles from a kit is pretty good value for money, $195.99 divided by 2000 is 10p a mile https://youtu.be/QEFZ-low5Fg
  8. I

    when everything is new and it still wont go

    https:swBDlOk0V6Y
  9. I

    when everything is new and it still wont go

    https://youtu.be/swBDlOk0V6Y
  10. I

    when everything is new and it still wont go

    test post <iframe width="560" height="315" src="https://www.youtube.com/embed/swBDlOk0V6Y" title="YouTube video player" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe>
  11. I

    when everything is new and it still wont go

    yes, felt like a phase was out, if they will run at all with a phase down, also would not run at all until i turned off and back on
  12. I

    when everything is new and it still wont go

    my bike went down on speed and was running rough, battery fine, not tested the rear hub yet, assummed it was the controller, bought one from ebay, advertised as a twelve tube controller,still no luck, may get one of those multitesters next i suppose, any one ha any experience of these 500 watt...
  13. I

    Ebike riding with a speaker and lots and lots of lights?

    love to get the tunes belting out and full disco lights, its a personal mission of mine to introduce the world to the music of the cramps,
  14. I

    Waterlogged lite speed lite bee battery

    thats why IP65 enclosures are such a bad idea, they always fail on the top, because the sun hits the top,IP44 is much better, an IP 65 enclosure can be converted to IP44 by drilling a 3mm hole in the bottom, the water can get out faster than it can get in
  15. I

    if carlsberg made spot welders

    updatet,welds are poor, too much heat,deap indents in cell base,a bust
See more
Back
Top