Recent content by mauri_78

Hi all, i have a question regarding the setting of menu 7.2 in opensource firmware. In this menù you can set the current ramp up, the default value is 5A/s, in your opinion which is the highest value that can be setted without make any damage? I have tried to increment this value and i have seen...

Hi all, I have a problem with my TSDZ2, after 1500km it bacame noisy... I have suspected some problems in ball bearings or in blue gear so i have totally disassembled the motor but all is ok! the blu gear is still perfect and all the ball bearing are ok. I have also opened the brushless motor in...

Hi rba, for sure i can share stl files, i will upload them to thingverse. I have used the pogopins that i had in my home... i can measure with caliper the diameter, lenght ecc. Abou the wiring i made a lot of photos, so this isn't a problem. Till now i don't have brake switch but i can easily...

Hi all, In order to install FW mod without cutting wires and with the possibility to use the throttle and brake cut off connected on original VLCD5 bracket i have designed an adapter for KT-LCD3. With this adapter you can plug LCD3 on VLCD5 bracket. I have also added a connector for upgrading...

Hi casahino, thank you for you rapid response! Yes probably i have made this mistake! For sure i will make more tests, but i think that you are in right! best regards Maurizio

Hi Buba, thank you very much for your work! I have removed the battery from my bike and i have noted that when you remove the battery the trip counter is resetted. To be more precise when you remove the battery and then you reconnect it the trip counter indicate 1km. I'm running 0.19.0 version...

Hi all, i have noted that removing the battery the trip counter is resetted... Is possible to store trip counter in eeprom for next versions? Sometimes is useful to park the bike without the battery that can be removed for charging... would be nice if trip counter wouldn't be resetted in this...

ERROR IN BATTERY VOLTAGE READING for 36V battery. Hi all i have noted that there is an error in voltage reading. with the battery full just disconnected from the cahrger i measue with my fluke multimeter 42V instead on lcd03 display i only see 41V. I have done this measurements with the bike...

Hi, i finally have upgraded my tsdz2 with open source fw! I have a doubt regarding configuration. What is the behaviour of 7.1 parameter? I have read in the manual that this is the motor power limit. I have set it to 350W but i have seen on the motor power field that the instant power goes...

Hi, i haven't erased but before i had stock firmware. This is my first installation of open firmware. Do you think that i should erase all and then reflash? I was thinking to downgrade to 18.2 i have seen that there are a lot of users that are experiencing problems with 0.19.6 version. Someone...

Hi guys, I need some help, i have installed FW mod on my tsdz2 version 0.19.0 beta 6. The problem is that the navigation in the configuration menù is not as described in the wiki, i see 10 menus instead of 9 and i'm not able to save settings. In i'm on configuration menu 0 and i push down the...

I just want to thank casainho for the great work! From italian forum jobike we are following with a great interest the development of the open firmware and some users reports a great experience with this firmware. This is the link to the discussion regarding open firmware on jobike...

Ok, short trip counter is for sure a function nice to have :-). In my opinion is better to quickly cycle between short trip, trip and total counter as you can do in all car's and motorbike's cluster. Reset and set of total km instead is perfect in configuration menu. Maurizio

First of all Thank you very much casainho for your work! It maybe a solution... in my opinion the better and simpler solution is something similar to the one implemented in VLCD5. A total kms counter(not resettable or resettable with a menù function) and a trip counter that can be resetted in a...

Thank you very much casainho, but haven't understood well: is possible to reset the trip distance and mantain a total km counter? Should also be useful to have the possibility of preset a total km value in order to mantain the total km till now.