Recent content by wyvernwaddell

Thanks, y'all-I've thought about a BBS02 or BBSHD also, but wasn't sure the weight on the boom would be ok. I haven't had a chance to do a lot of research yet as this is just in the planning stages at the moment. Judging from the number of builds I've seen with those just in the past couple of...

I have a Catrike Expedition with 135 rear drop out for 26 inch wheel. I'm trying to find a 500 watt hubmotor that will take a 10 speed cassette (NOT freewheel) and fit in the dropouts. Might be willing to go with less wattage if that means it'll fit in the dropouts and I'm aware that I can add a...

Thanks man-i got it figured out.

Would really love to know if tangentdave will sell me a 3210 tangent controller-I nuked mine. I had one of the very first few units-and it's been great. Barring that-has anyone successfully hooked up a Phaserunner to one of these?

I can't find a phone number for them and I've been trying to contact them for a month (via the email on their site) about a controller. Anyone know how to contact them directly? Would sure appreciate the help if someone does.

Well, I don't want to weld the ones I have-they fit every other bike motor I've ever seen and I may want them for a different motor in the future. What I hope to find is someone that can cut some for me if I send pics and measurements. They are just flat triangles with holes-if I had equipment...

Great build! Looks like a lot of fun :) Might you remember what size the axles are on the TDCM motor you installed (between the flat sides and over all? I'm trying to have torque plates made to install this same motor on my bike.

I bought a TDCM DD hub from Grin Tech http://www.ebikes.ca/shop/electric-bicycle-parts/motors/igh-395.html The axle seems to be a bit smaller than the standard 12mm I've seen on the other ebike hubmotors I've had. Is there someone on here that's US based that might be able to make me two sets...

Well, whadda ya know..flashed back to stock with the quality control .xml that Justin posted a few posts back and then set my CA at starting regen at .50 volts minimum time .5 seconds and it works perfectly. I now have regen! Hey Cycborg, you might want to try flashng that .xml before you play...

Well, we have 2 bikes here..one is my Mac, the other is a Crystalyte DD hub. I'm the mechanic in the household, so I get to fix things. Since getting the PRs was my idea- I REALLY get to fix things. I'm trying to figure out regen on the Crystalyte at the moment. The bike works fine without...

Thanks for the help, Sir! Ok, I did the two things you listed and now, when I go test the bike, the throttle doesn't work anymore and trying to rotate the pedals produces a pulsing action. If I stop turning the pedals, the pulsing stops. I haven't changed any other settings.

Hi everyone :) I'm trying to set up regen braking on my Phaserunner. I have it plugged into my CA. The brake lever is just a regular on/off brake signal that I have plugged into the ebrake connector on the CA. When I hit the lever, the little lever in the display works and the motor cuts off...

Much thanks, Justin :) I managed to muddle my way through the whole mess..but you can bet I will be keeping that .xml file somewhere safe for when I somehow manage to do it again. I seem to be all thumbs some days... Both of our bikes are running quietly and beautifully currently...I may do a...

Anyone know what Fault 13 Internal Error means? I'm trying to autotune my PR after buggering up somehow and that's the only error I don't seem to be able to find a way to clear. Also, is there a default .xml for BACDOOR that I can load to get my settings straightened out? Any advice much...

Anyone know what a 4-6 or 6-4 blink code is? I had everything plugging along fine..turned off the power, unplugged my cable, turned the bike back on and I get that blink code and the Phaserunner software won't connect now. The bike turns on, the CA turns on but nothing happens when I hit the...