• Howdy! we're looking for donations to finish custom knowledgebase software for this forum. Please see our Funding drive thread

Recent content by yumseyo

  1. Y

    Bafang BBS02 48v on to a Rigid Carbon Frame fitment ?

    Hi all !! I just got my hands on a Bafang BBS02 ebike conversion kit and was wondering if anyone with Bafang experience could look at my pictures and advise if I should continue the install and if I might have any problems. I was able to slide the motor onto the bottom bracket but wanted...
  2. Y

    PAS does not work

    No, I just gave up on the PAS ( I took the magnet disc and used it on another bike..hee hee) The bike will hardly be ridden and I figure pedaling without assist would give more control on motion vs the assist which may cause a loss of control of the tricycle. I contacted the seller on Amazon...
  3. Y

    PAS does not work

    Would I better off upgrading the controller? If so, is there a kit anyone could recommend that would give me an upgraded lcd and the PAS system or would I still run into compatibility problems of parts..
  4. Y

    PAS does not work

    Thanks for the reply e hp. Can you teach me how to determine the signal and ground wires. I think there were only three wires on the connector.
  5. Y

    PAS does not work

    Thanks for the reply. The connector was the same. Maybe the wires are in a different order? The red led on the pas unit does flash when the crank is turned though.
  6. Y

    PAS does not work

    Thanks for the reply. I got a troubleshooting guide with the kit, but it doesn't talk about the PAS system. I've attached pictures of the "normal" controller, which is what I've set up on the bike. Throttle works fine but PAS lights up but doesn't activate motor. My thinking is that I need...
  7. Y

    PAS does not work

    Hi ALL ! I was hoping to get some technical help. I bought a motor kit from Amazon and got it to work with the throttle supplied. The kit is...
  8. Y

    velomini battery wiring

    Hi All ! I was wondering if anyone can refer me to a site or help me with my velomini 3. I just got a used velomini 3 the powers up, throttle works, pedal assist works, but cuts off after 10 minutes of riding and won't power back up. after an all night charge, I get 28.4 volts at the battery...
  9. Y

    Bagang bb02 on tern link folder

    Thanks again Footloose. What size chainring did you use to get that 30 mph? Also what kind of chainring did you use to get the right chainline?
  10. Y

    Bagang bb02 on tern link folder

    Thanks Tom ! I will measure my chainline..
  11. Y

    Bagang bb02 on tern link folder

    Thanks so much for the reply. I wanted to go with the 48v unit because I thought I could go FASTER with it. What was the top speed of your Raleigh ? Maybe I could mount the battery under the forward part of top tube? I am about to re assemble a Bionx Dahon folder and was going to put the...
  12. Y

    Bagang bb02 on tern link folder

    Hi all, I am considering installing a Bafang BB02 750 watt 48v kit on my Tern Link . Can anyone tell me which chainring to get for the best chainline? I will probably get a rear rack for the battery, and I want to keep my 10 speed rear cassette with Di2 shifter. Thanks in advance for all your...
  13. Y

    Anyone have an "ADD-E" 600 watt friction drive kit ?

    Hi All, Would anyone give their experiences with the new ADD-E 600 watt friction drive ebike kit with throttle? It is a friction kit and is very light. I am considering buying one, but was hoping someone could help me decide one way or other. Here is a link to their website...
  14. Y

    bionx g2 bench testing

    Well, I just got my wheel back from modification. Speed goes up to 25 mph now.... :( I thought I could get more, but the assist restriction has been disabled so I should be able to get it into a higher gear and assist the bike faster...I hope..
  15. Y

    velomini battery wiring

    Hi All !, I was wondering if anyone has any experience with troubleshooting the velomini 1 folding ebike. I got one that did not have a battery. According to the previous owner, it was working, and all that was needed was a battery. Well........... I just installed an external battery, 24 v...
Back
Top