Search results

  1. S

    TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

    That’s where I went wrong…. Rookie mistake! Thanks for your help @endlessolli… much appreciated 👍
  2. S

    TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

    I followed the Temp Sensor Install Wiki instructions for 8 pin controllers. It says to cut the throttle wire and connect the centre leg of the sensor to that wire. I assumed the sensor is connected to the end of the wire that goes to the display (and not to the end of the wire still connected to...
  3. S

    TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

    Thanks for your suggestions. I have triple checked and tested my wiring but can’t find a problem there. With the battery & display on, I’m getting 4.3V with correct polarity between the sensor’s 5V & GND legs. I have continuity from the centre leg of the sensor (Vout) to the throttle pin on my...
  4. S

    TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

    I bought from a trusted legit overpriced retailer (not eBay) - RS Components in Australia. As I said in my initial post, I tested the chip before installation and it was working as it should.
  5. S

    TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

    Hello, I need temperature sensor help please? I’ve just installed a temp’ sensor (LM35DZ) following the wiki instructions for my 8-pin connector (VLCD5). After I re-flashed the @mbrusa OSF to enable the temperature sensor, the temp display is fixed at 18.3 degrees. Everything else works fine. I...
  6. S

    TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

    @mbrusa it might help troubleshooting if you know I am a big/heavy guy… 103kg. Maybe I’m asking too much from the TSDZ2 and the real solution is I lose weight.
  7. S

    TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

    Yes, you’re correct. Also, it goes away if/when I can push through the problem and increase cadence. Problem is intermittent… not always there. I’m starting to wonder if there is a hardwired temperature or power/current limiter built into the TSDZ2 that is overriding your firmware.
  8. S

    Hardware temperature control tsdz2

    Hi Everybody, Noob here but I have learned a lot scanning/reading through this thread, thank you. I’m hoping someone can recommend an online seller for decent quality and value thermal pads please? Bonus points if the seller is in Australia 🇦🇺. Thanks 😊
  9. S

    TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

    In case you are asking me (about my post on Nov 27 - TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.): Yes, I am using hybrid mode 52:11 (top gear) when I notice the intermittent issue.
  10. S

    TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

    Hello, Old guy here, new to OSF, but have been using a TSDZ2 for about 4 years now. First I want to say a massive Thank You to @mbrusa and any other wizards who have made this OSF possible. It's awesome! I flashed my road/touring bike yesterday and love how it performs, but am having one...
Back
Top