Search results

Date Relevance Most replies

  1. L

    IS PM DNM USD-8a Tektro Auriga e-twin Adapter

    Hi, i have a DNM USD-8a Fork and a Tektro auriga e-twin. out of the box both do not fit together. The auriga seams to be a standard pm but what adapter do i need to get it mounted on the fork? Thanks for a hint. Tektro Auriga e-twin Mountingpoint for the adapter on the fork Adapter i need
  2. L

    18650 stationary storage

    I have a channel abo from the electric samba jehugarcia too. He dont use active BMS but he check the cells from time to time manual. He charge not to 4.2 cell voltage go have a buffer for drifting modules. Jehu has driven a few hundred miles without problems caused drift. So for his usecase it...
  3. L

    18650 stationary storage

    i don't buy new 18650. i recycle old laptop batteries. so my price per kWh is 50 Euro. i use 75-80% of their capacity (4,1-3,5v) they never get hot because i charge and discharge them with less then 1 amp per cell. in my celler the temperature is between 16 - 20 celsius. Lead acid where never an...
  4. L

    Homemade Battery Packs

    The purpose is to charge when the sun is shining and my solar panels generate more power than my house need, store it and use it at night. In Germany i have to pay 30 cent per kWh from grid. sure i also can sell the kwh for 12 cent to grid but it is cheeper to use the maximum by myself...
  5. L

    Homemade Battery Packs

    Thanks for all the information. They was very helpfull to get my DIY Powerwall project work. bBzPAQejyTA
  6. L

    18650 stationary storage

    At the moment i balance when charging with revolectrix cellpro. I build 30 modules with 42cells each. The current setup is 6s210p (5 modules in paralell). Later i´ll use the modules with sunny island as 15s 84p (2 modules in paralell) and a BMS from REC that can communicate with the SMA Sunny...
  7. L

    18650 stationary storage

    After two years collecting laptop batteries i got good usable 8 kwh capacity i soldered to modules. For sure cell fused. Now, i´m wayting for budget go get the charge and reload to grid automation. bBzPAQejyTA
  8. L

    Cute q100 pole speed problem

    finaly i used an extenel speed sensor for ca and programmed the controller to trottel 100% at all three speed switch options. i dont use a speed switch. that was the reason for the speedlimit.
  9. L

    Cute q100 pole speed problem

    Thanks for your answer, i tested with 1000 Watt and 20a limitation but the speed wont increase. The big question is why show the cycle analyst 3.0 the wrong speed info to me? Are the pole settings i configured correct? I read that there are 10 pairs also 20 poles to configure. What reason...
  10. L

    Cute q100 pole speed problem

    Hi, i installed a Cute Q100 201 rpm 36V motor into my wifes 700c Bike. Controller is a 12fet infineon. Akku LIPO 12s2p. Cycle Analyst Limited to 15a /750Watt. Power can be adjusted over Pas Poti. Problem. The Motor should have 10 Pairs of Magnets. Whey i configure 20 pols in CA the ca give me...
  11. L

    Infineon 4110 12 FET wont accept throttle from CA

    Hi izeman, yes thanks a lot. I asked the Shop for an appointment do do the change. Hope they get the 1k resistor soon that my system will run next days with throttle over CA.
  12. L

    Lyen 12 FET - Crystalyte HS3540 grunt like a little pig

    Hi John, Friday i visit my local Store and bought a infineon 4110 12 fet controller. With this controller i found the right combination in 2 minutes the motor is running very good. the speed is a bit slow for 75v only 40 km/h but it works. So my Lyen 12 fet have to be defect. The Problem with...
  13. L

    Infineon 4110 12 FET wont accept throttle from CA

    Hi, i bought a brand new Infineon 4110 12 FET Controller. Throttle from ca wont be accepted. i read that the new controller don´t have problems with ca. Older versions can work with a workaround but i dont want to tinker. is there a programmable solution to make the controller run? Thanks Lory
  14. L

    Lyen 12 FET - Crystalyte HS3540 grunt like a little pig

    Tested Hall everything s fine. Tested Lyen 6fet controller without hall motor run very fine. I Testet with my throttle and my ca. Lz2HKD41jR8 Looks like an problem with the controller. Tested the hall cable between controller and Motor all lines are ok. I have no Idea. My Lyen 12 fet hall...
  15. L

    Lyen 12 FET - Crystalyte HS3540 grunt like a little pig

    Changed the Video. blue - green crossed Hall. It seems that i have to test all the 36 combinations to find the correct one.
  16. L

    Lyen 12 FET - Crystalyte HS3540 grunt like a little pig

    At this Video i changed the green and the blue hall cable i am not sure about the flashing... I7Xk3KAqOgw
  17. L

    Lyen 12 FET - Crystalyte HS3540 grunt like a little pig

    Now i checked the controller. Are the LED´s rotating on the right way? http://www.youtube.com/watch?v=43HWsLYHPgE 43HWsLYHPgE When i cycle with the actual Cabeling, the CA switch power on although the akku is not connected when i cycle faster than 14 km/h With the tester i verified that the...
  18. L

    Lyen 12 FET - Crystalyte HS3540 grunt like a little pig

    Thanks for the link. Yes i tryed the combinations in the instructions from Lyen for hall. The phase wires are not colored because cables was changed to AWG14 inkl. Temp Sensor was installed. But i tryed every possiblephase line combination.
  19. L

    Lyen 12 FET - Crystalyte HS3540 grunt like a little pig

    Double checked hall colors - black - black, red - red, yellow - yellow, blue - green, green - blue. Tryed all phase combinations. The video shows the best result i could get.
  20. L

    Lyen 12 FET - Crystalyte HS3540 grunt like a little pig

    Hello, can anybody please analyze the sound came out my Crystalyte HS3540. VfYTi7P4ykk http://www.youtube.com/watch?v=VfYTi7P4ykk Thanks
Back
Top