Search results

Date Relevance Most replies

  1. P

    Wireless Wii Nunchuck *TESTERS WANTED

    Hi, I have no issue shipping overseas if you are after a ready made board. http://www.homanndesigns.com/store/index.php?main_page=product_info&cPath=51&products_id=278 Cheers, Peter
  2. P

    My Hubmotors arrived..Build log

    Hi, I could probably make some up on my small CNC mill. Can any one send me an accurate drawing of the dimensions? Cheers, Peter
  3. P

    Mini Wii Nunchuck Receiver ***TESTERS WANTED ***

    Hey Guys, Just a quick note. For those that have been emailing, the MiniWiicever is now back in stock. If you need a Nyko remote, you can bundle that with the MiniWiicever. http://www.homanndesigns.com/store/index.php?main_page=index&cPath=51 Cheers, Peter
  4. P

    10S custom skate ESC: testers wanted!

    I would expect that the NRF24L01+ would be a better solution than Bluetooth. The control required is relatively basic and in my opinion doesn't warrant the complexity and cost of Bluetooth. Cheers, Peter
  5. P

    Simple Charging Port (Plug n Play)

    The data sheet says 7.5A. Yes, that would be per pin. http://media.digikey.com/pdf/Data%20Sheets/ITT%20PDFs/DE9P.pdf But as you know, in the end I used one of you pre-built charging cables. Life is too short to be soldering cable connectors. :) Cheers, Peter
  6. P

    Simple Charging Port (Plug n Play)

    Hi, A quality 9 pin D-sub connector such as this one is rated for 7.5 Amps, more than enough for most chargers. http://www.digikey.com/product-detail/en/DE9P/IDE9P-ND/2580862 Cheers, Peter
  7. P

    TorqueBoard's Dual 63mm SK3 on 6" All Terrain Setup

    Thanks for that, it looks like just the ticket. Cheers, Peter
  8. P

    TorqueBoard's Dual 63mm SK3 on 6" All Terrain Setup

    Hey Psychotiller, Where did you get this deck from. I'm looking at doing a all terrain board and this deck looks ideal? Cheers, Peter
  9. P

    Compression Molded Carbon Fiber Deck

    I'll take a pair as well. Cheers, Peter
  10. P

    Mini Wii Nunchuck Receiver ***TESTERS WANTED ***

    Hey Benj, Great to hear. :D Cheers, Peter
  11. P

    Mini Wii Nunchuck Receiver ***TESTERS WANTED ***

    Another batch of boards fresh out of the pick and place machine, ready to be programmed and tested. This batch is all taken. Cheers, Peter
  12. P

    Compact Motor Mount and Longbuild build

    Hi All, Well, the longboard is finally done for now. I have a list of improvements that I would do if I was to build another board. I leant a great deal along the way. Thanks for all the help from everyone who chimed in. The board is running Homebuilt maple veener deck Calibre 50 trucks ABEC...
  13. P

    Evolve Carbon All Terrain's Catching Fire!

    It looks like they succeeded in silencing you after all. Cheers, Peter
  14. P

    Enertionboards.com | 5x1.5 Inch All-Terrain-Wheel

    Hi Sebastien, The best way to work out the belt length is use this calculator. https://sdp-si.com/eStore/CenterDistanceDesigner According to it the diameter of a 64 tooth 5mm HTD pulley is 101.86mm (4.0102") Cheers, Peter
  15. P

    Enertionboards.com | 5x1.5 Inch All-Terrain-Wheel

    I think I need a set of these. :) Cheers, Peter
  16. P

    Compact Motor Mount and Longbuild build

    Thanks, The board is for my son. I might get to ride it a bit, give it a test run, that sort of thing. Cheers, Peter
  17. P

    Compact Motor Mount and Longbuild build

    These pics show then enclosure with power applied. I was just doing a bit of testing to check a few thing out. As you can see it is quite handy being able to see the status LEDsof the MiniWiiceiver and the Wii remote receiver LED. That's about it for the update for now. I'll do a set of...
  18. P

    Compact Motor Mount and Longbuild build

    The next step was to drill the mounting holes for the front panel. The panel includes the charging jack, on/off switch and key switch. And, with the panel mounted. Cheers, Peter
  19. P

    Compact Motor Mount and Longbuild build

    The MiniWiiceiver now mount to the top half of the enclosure. I also put in some 5mm flat top LEDs so that the status of the receiver can been seen once everything is assembled. The MiniWiiceiver mounts in as shown below. Cheers, Peter
  20. P

    Compact Motor Mount and Longbuild build

    Hi All, A bit more work on the board over the weekend. I've decided to mount the MiniWiiceiver into the top half of the enclosure, so I cut the integrated mounts off the bottom half. I also finished off the bottom half of the enclosure. This is the top half mounted to the bottom half...
  21. P

    Mini Wii Nunchuck Receiver ***TESTERS WANTED ***

    Hey Benj, Have you given it a run with the Miniwiiceiver yet. Cheers, Peter
  22. P

    Mini Wii Nunchuck Receiver ***TESTERS WANTED ***

    That look great, really compact. Cheers, Peter
  23. P

    Compact Motor Mount and Longbuild build

    Hi, It's quite rigid. With the top half on it will be strong. The board has a bow in it and flexs a small amount. The enclosure will be attached by four M5 bolts with Nylock nuts. I'm assuming that the enclosure will reduce the flex, but I'm not completely sure how it will go. Cheers, Peter
  24. P

    Compact Motor Mount and Longbuild build

    Just a quick update and incremental progress. I made the cross bar support to provide protection to the motors and to square up the mounts. If I was to do it again, I'd also put another support bar close to the truck. Cheers, Peter
  25. P

    Mini Wii Nunchuck Receiver ***TESTERS WANTED ***

    Hi Ben, Glad to see it arrived. Post a pic once you have it installed. Cheers, Peter
Back
Top