Search results

Date Relevance Most replies

  1. P

    EU Phaserunner/cycle analyst v3

    I have a new Phaserunner with BBSHD harness and cycle analyst v3 bought from Fasterbikes.eu I just tried to configure it for bbshd but i not continue, lack of free time and i just ordered a Frey Ex -External speed sensor it's not connected , i buy the cycle analyst without it but i add a spare...
  2. P

    self learning on controller vs 3 position speed switch.

    It should be the same for all 3 speed modes, you don't have to connect the self learning for each . Maybe this is the way the controller reacts when you try to switch the modes under power. I use the 3 speed switch with cycle analyst and when I use the throttle it cuts power for a moment
  3. P

    BBSHD Error Code 08

    I have this code 8 error 2 times on my BBSHD . The motor its new, I use the bike 2 days to go work, 14km one way , 3-5°c. I get to work, everything ok, after 9h, the bike sit outside, same temp, when I want to leave code 8 error. My friend push me with his bike so I don't pedal all the way back...
  4. P

    'lightest.bike' 1.7kg 1000w mid drive

    There will be available different bottom bracket sizes , 100 or 120mm?
  5. P

    Compact Field Oriented Controller, ASI + Grin, limited run

    Hi, anyone use the phaserunner with a bafang fat motor , G060? I have the 750w rear motor, I did the autotune but when I apply throttle the motor its juddering , feels like the power it's pulsating to the motor. I have the cycle analyst v3 for a few years and just updated to last version now...
  6. P

    Dapu hub motor compatible controller.

    Yes , it's the speed sensor. I see it on many bafang motors without halls.
  7. P

    New line of budget in-frame triangle bags

    You could fit ~150 cells + BMS in the em3ev bag
  8. P

    BBSHD controller on hub motor/hub controller cutting power

    Hi, I read many topics here but I didn't see anyone trying to connect a BBSHD controller to a hub motor. I have a 750w bafang fat motor and I try 2 controllers but both are cutting power after a while when the battery is full. First I use a 25a 9fet kt controller and after I change to a 30a...
  9. P

    Alarm integration with Kelly controller 7230s

    You can tell where the wires go?
  10. P

    Hall sensor pinout

    Yes, I leave only the board with hall sensors, take the wires out from them and motor phases. I try first with a square wave 250w controller but it doesn't work well, too loud and jerky. I change to a sine wave controller and it works great but I use it on 48v and 30a and break a few teeth on a...
  11. P

    Hall sensor pinout

    Meanwhile i read about capacitors and they are linked to ground. On the board the capacitors are between signal and gnd. I will let them i guess they dont make any harm if shimano use them. Going to solder the cable, i hope this week i will test it. I am curious if i can use the torque sensor...
  12. P

    Hall sensor pinout

    Do you think its ok to use the board how is now? Betwen each sensor signal and +v/gnd is a smd capacitor. The capacitor is used usually betwen +v or gnd? Should i remove them? Thank you
  13. P

    Hall sensor pinout

    Sorry but i dont see any usefull information in your image. I see on many diagrams that Gnd is pin 2 but some its pin 1
  14. P

    Hall sensor pinout

    Hello, i need some help to find + and - pin on this type of hall sensor I think + its pin 2 and - pin 3 but i am not sure . The board its from shimano steps e6000 motor. I want to connect to external controller and use it with throttle. W10b smd hall sensors
  15. P

    Homemade Battery Packs

    Hello, this is my first post here but reading this forum for ~2 years. I just bought a spot welder (sunkko 709ad+) and made a 12p10s battery using panasonic pf cells. Now i dont know if i should put on a cheap bms from ali or should i use one from hilti tool packs. They are 36v and at least 30a...
Back
Top