Not much at all. This bike is basically gonna be a streetfighter with very minimal electrical. Headlight, taillight, signals, and maybe a horn. All LED should put me around 100W max for everything.
Also, FYI, Heltec sells a BMS that's basically exactly what has been proposed...
Thanks for the link, I see what's up now. I had a feeling it was something to that effect, this confirms it.
I will be using a 12 VDC converter for the accessories on my project so I'll probably go with a 12 VDC contactor, but I see your point with going to pack voltage. I may still...
Hello. Not trying to sound pushy here but did you ever whip up a simple drawing of this wiring? This solution sounds perfect for my high-amp pack I'm putting together for my EV Motorcycle. I'm using 5 Headway 38120's in parallel (28 in series) for an easy 600A instantaneous discharge. Thanks.
I got the size 6 because it came with the motor. Motenergy sold them to me together for $900 back in 2018. It was oversized, but also a steal so I took it.
I'm guessing 50A because that's what the cruise amperage is around. Heavy gassing is up by 600A, but that's only about 1% of the time...
Hello
I'm currently building a 28s5P pack for my ME1507 and Sevcon Gen4 Size6 controller for the EV motorcycle I'm building. I've got the batteries on the way (Headway 38120 LiFePo4 cells) and thanks to their phenomenal discharge capacity, I'm fully expecting to be maxing out the amperage of...
Cool, thanks for the tip. I was speculating that might be the case, I just didn't know what it was technically called. Same with gas engines (light throttle in neutral revs higher than under load). I swapped the encoder leads and the motor didn't spin at all so I know everything's wired...
Back in 2018 I bought an ME1507 and Sevcon Gen4 Size 6 directly from Motenergy, and had Frodus program the Sevcon and supply his wiring harness for it. Then life got in the way...
FFWD to yesterday, I finally got around to bench testing the rig using two of my Ego lawnmower batteries in series...
Thank you, but I'm not enough of an EE geek to understand fully what you're saying. I lost the EE desire after Circuits 1 and stayed ME
Maybe I should have said, where can I a PCB based battery maintainer for 24 cells? Or 8x3 cells? Or 6x4, etc...
Why do some of the cheap PCB versions of BMS's say they have a charge/discharge amperage rating, and the Orion or Dilithium Designs say nothing about charge/discharge amperage? Also, if you look at the Tesla BMS that comes built into each pack there is no large cable running through it, just...
That's the ME1507, and technically Motenergy designed it and made the first few for Zero, then Zero cut them out and had them manufactured elsewhere.
Zero doesn't make motors, they build motorcycles.
Yes, I know this is an old post.
Wow, I really appreciate the answer there but in all honesty, only about 25% of it I actually understand.
I know what a resistor is and what ohm's are
I know what a 555 timer is but not how to use it
That's about it.
Right now the "fuel level sensor" on the Koso gauge is designed to read a...
Sweet! Now how's a mechanical engineer go about making that up? :oops:
I suppose a blank PCB with them two chips is a start? I can solder, that I've got down. I'll have to get my pack voltage down to reasonable levels with a voltage divider cause I assume them chips can't take 105VDC.
You're welcome
Be advised, on my 2011 XU a lot of the information between everything on the bike went thru the MBB (which I tossed in the trash on my build). Depending on your build you may be better off wiring direct between speedo and whatever device you're measuring. Heads up on the...
That's a Koso RX-1N
https://kosonorthamerica.com/shop/motorcycle-mx/rx-1n/
And here's the "pinout", which you'll have to reverse-engineer:
https://kosonorthamerica.com/instructions/BA011B02.pdf
BTW, this is a great Zero resource:
http://zeromanual.com/index.php/Unofficial_Service_Manual