Search results

Date Relevance Most replies

  1. D

    TSDZ2 mid drive with 860C, 850C or SW102 displays only -- Flexible OpenSource firmware (Casainho code only)

    My first try would be: Disconnect the batteries, swich on for discharging the system, replug batteries , swich on and dont touch the pedals for 5 seconds. Second, please check Motor ands Batterie parameters in the setup, Try to make a test drive with a few minutes with a intermediate...
  2. D

    TSDZ2 mid drive with 860C, 850C or SW102 displays only -- Flexible OpenSource firmware (Casainho code only)

    Found it :-) For people who dont find: It is behind the highest support mode (9 in standard config) For me 9-10 is the best value for E-MTB sensivity.
  3. D

    TSDZ2 mid drive with 860C, 850C or SW102 displays only -- Flexible OpenSource firmware (Casainho code only)

    Sorry, then I have some questions with the modes: Should I only enable one mode in the configuration? If so, what will happen if I will enable two different modes? If not, How to change from mainscreen? I did not find the method to swich! Regarding MTB Mode: just to ned to put on the...
  4. D

    TSDZ2 mid drive with 860C, 850C or SW102 displays only -- Flexible OpenSource firmware (Casainho code only)

    I installed 0.20Beta1 Yesterday from Github Did cadence sensor calibration / advance mode during setup, My cadence is shown OK, a little bit flickering up and down ( +/- 2) Was working fine on first test drive, working very smooth and nice! Was a little confused by the changed...
  5. D

    TSDZ2 mid drive with 860C, 850C or SW102 displays only -- Flexible OpenSource firmware (Casainho code only)

    I am not good in programming but I found following formular: 95.5 * (1/0.637) = 150 ... Shouldn't it be 95.5*0.637=60.8 instead , (I rounded from 0.637 to 0.5 , *100 , so find good corelation then ?
  6. D

    TSDZ2 mid drive with 860C, 850C or SW102 displays only -- Flexible OpenSource firmware (Casainho code only)

    Sorry, in my opinion, by doing these tests, you add a lot of uncertain factors: weight, steepness of road, speed, lost in the drive, lost of tires. Î did mesurments with a analog torque wrench, diretly on the axle . they where good repeatable would guess 10% error, see below. When...
  7. D

    TSDZ2 mid drive with 860C, 850C or SW102 displays only -- Flexible OpenSource firmware (Casainho code only)

    For me this is the only reliable way to calculate the expected range while riding. I have a battery with a quite high resistance (> 200 mOhm ) When I look at the current while I am standing still after a ride it is slowly going up during the first one or two in the range of 0.4V My...
  8. D

    TSDZ2 mid drive with 860C, 850C or SW102 displays only -- Flexible OpenSource firmware (Casainho code only)

    Hi, if you mean the backwards (forward) counting of the battery mW , then I can say that I am a fan of this feature and I use it regulary! For me one of the highlights :-)
  9. D

    TSDZ2 mid drive with 860C, 850C or SW102 displays only -- Flexible OpenSource firmware (Casainho code only)

    Yes,you are right There might be a bug in the calculation!! In my setup, at a cadence of maybe 90 it takes about (feeling) 20 Seconds to climnb from 70 to 89. Zero is reached in one second , when stoping pedealing, when I start agaín (feels like 80 to 85) it is starting with 50,then...
  10. D

    TSDZ2 mid drive with 860C, 850C or SW102 displays only -- Flexible OpenSource firmware (Casainho code only)

    Hi, I made mesurments with input by an old style analog torque wrench and the values shown at menue 9.2 Input Value 9.2 0 Nm 50 10 Nm 60 20 Nm 69 30 Nm 78 40 Nm 91 50 Nm (98) maybe not fuly correct I hope this helps to improve the calculation of...
  11. D

    TSDZ2 mid drive with 860C, 850C or SW102 displays only -- Flexible OpenSource firmware (Casainho code only)

    I think the function is implemented in the setup menue under item 7.2 Curent ramp up per second . Standard is 5, can be set up to 10. I would like to set it up to 12-15 if you ask me.
  12. D

    TSDZ2 mid drive with 860C, 850C or SW102 displays only -- Flexible OpenSource firmware (Casainho code only)

    Hi, I have installed 19.8 on 36V motor and battrie Thank you for this!!! - I like the new button logic. - The change from road mode to offroad mode I cannot real understand, because it is not logical to for me to swich to road mode through a button code. It is running well in my opinion...
  13. D

    TSDZ2 mid drive with 860C, 850C or SW102 displays only -- Flexible OpenSource firmware (Casainho code only)

    I like to have a good torque with low candence too, to pass crossings and pass mud holes you dont expect. Then I start below 50 cadence and enjoy / need the power. Just my two cents
  14. D

    TSDZ2 mid drive with 860C, 850C or SW102 displays only -- Flexible OpenSource firmware (Casainho code only)

    Hi, I had some requests regarding error blinking 1 and I have asked ho to make it better for me, because I sometimes got stucked on steep sections. But frankly spoke, I just swiched off the setting to power on without pedal rotation and I was suprized how fast the power came in the...
  15. D

    TSDZ2 mid drive with 860C, 850C or SW102 displays only -- Flexible OpenSource firmware (Casainho code only)

    Today happend again in the woods, Want to start a climb after pusing the bike, I was two times not fast enough to turn the pedal when going onto the bike (not usng brakes). Please tell me where is the code for this? , maybe have to fork to make tests if it is possible to make a "min...
  16. D

    TSDZ2 mid drive with 860C, 850C or SW102 displays only -- Flexible OpenSource firmware (Casainho code only)

    I am holding the brakes, (Old Hydraulic Hayes 9 DH breakes with 200 disks, but not compatible to sensor) of course! But my foot is just resting on the pedal without pushing. Thats why I am asking for a threshold!
  17. D

    TSDZ2 mid drive with 860C, 850C or SW102 displays only -- Flexible OpenSource firmware (Casainho code only)

    Sorry to say, but I am on last stable (18.2) comming from 10.x but this funktion as it is in 18.2 may make the bike more save for some riders with high power but is not nice with my way of riding. I never felt unsafe with older versions. What do you think about my ideas for...
  18. D

    TSDZ2 mid drive with 860C, 850C or SW102 displays only -- Flexible OpenSource firmware (Casainho code only)

    As I understand it, it is a safty feature for- -Saving the blue gear , specaly on high volltage , one may damage the gear when standing on the pedal and holding the bike with the brakes - when you have a crash, and a pedal may hang somewhere and the motor is pushing against this...
  19. D

    TSDZ2 mid drive with 860C, 850C or SW102 displays only -- Flexible OpenSource firmware (Casainho code only)

    Hi, Regarding Blinking 1, I see the use of it , but also feel the problem in traffic light, or when you just stop and talk with friends, My saddle is quite high, so my foot is restng on the pedal when I stop. I am wondering if it is possible to - have a threshhold for torque before...
  20. D

    New "TSDZ2 Torque Sensor Central Motor"

    I have installed 18.2 on a 36 V motor, The 48 V Option is NOT working on a 36 V engine with 36V batterie. Option 2 Running well if you are a fan of high cardence. Option 1 is prefect for me would guiess to have Support until 90 . Regards Dirk
  21. D

    New "TSDZ2 Torque Sensor Central Motor"

    Please look! https://www.eco-ebike.com/blogs/eco-cycles-instructionals/tsdz2programmingfromscratch You can adjust the 36 V Engine and original display to 48V and have higher cardence
  22. D

    TSDZ2 mid drive with 860C, 850C or SW102 displays only -- Flexible OpenSource firmware (Casainho code only)

    Sorry I was so wrong! I installed 18.02, (after having 10 or 11 for almost 8 Months) I also got "blinking 1 ", Maybe somebody of the developers can tell what is the reaon for this to run into this fault code? In my opinion it was something with Start / Stop? Never had this with the old...
  23. D

    New "TSDZ2 Torque Sensor Central Motor"

    Hi, during Easter Holyday I was using my bike with engine swiched to 0 for several kilometers over one week. For going into the Hills around Garda I used the support of course, but for the rides along the lake I was riding very well with 0 support. In my opinion, the efect of a poor...
  24. D

    TSDZ2 mid drive with 860C, 850C or SW102 displays only -- Flexible OpenSource firmware (Casainho code only)

    Hi, could it be that you stand on the pedal while waiting? I think there is a timeout of 5s (10s at 19.6 ) leading to this.
  25. D

    TSDZ2 mid drive with 860C, 850C or SW102 displays only -- Flexible OpenSource firmware (Casainho code only)

    For somebody who is programming / coding every day, this seems to be easy. The tools are new for me. To do changes, I do not need to understand the whole system. It is a changeling for me ! That's why I was asking if handy tools can help me. Your guys real write the HTML directly into...
Back
Top