• Howdy! we're looking for donations to finish custom knowledgebase software for this forum. Please see our Funding drive thread

Search results

Date Relevance Most replies

  1. E

    Controller for Golden Motor Hub?

    Is that with the stock phase wires? I am at 30 and 80 now.
  2. E

    Controller for Golden Motor Hub?

    Yep, that was it. I did not know I was looking for "Halt V." I did not know what that was so I did not mess with it and instead overwrote it with the default 57 which was 1 volt more than I had at the time. After I told him I killed it, Edward sent me the complete spec that I had been asking...
  3. E

    Controller for Golden Motor Hub?

    I did not set out to change the LVC but now that you mention it, I bet that is what I did. Can you change just one thing or do they all get updated at once in the flash? I suspect the latter and that when I loaded the default file and failed to find an item labeled "LVC" to change, I ended up...
  4. E

    Controller for Golden Motor Hub?

    I bought the 12 X 4110 Controller from Lyen and it worked fine until I tried to program it. Its a real problem that the software does not let you retrieve the current settings. My motor no longer runs. Does anyone have an .ASV file for a 12 fet infineon and a Golden Motor 48V, 1000W motor...
  5. E

    Controller for Golden Motor Hub?

    I now have an EC-12411OLD Lyen Edition controller with the programming interface, 3 way switch, cruise control, and "CA" interface. I also have a new throttle which I also got from E. Lyen. I am assuming that "CA" means "Cycle Analyst"? I am running 48V now but have another 24s worth of good...
  6. E

    Controller for Golden Motor Hub?

    Thanks, Phil, I have placed an order with Edward.
  7. E

    Controller for Golden Motor Hub?

    http://kellycontroller.com/keb4822124v-48v-100a22kwe-bike-brushless-controller-regen-p-59.html • Support three modes of regenerative braking: brake switch regen, release throttle regen,0-5V analog signal variable regen. What is this 0=5V analog signal variable regen?
  8. E

    Controller for Golden Motor Hub?

    The infineon's look nice and seem to be reasonably priced (a Golden Motor controller shipped from China is $90) but they all seem to have long leads where I have long leads coming out of my GM wheel. Is the Infineon lead something special that I should solder into my hub or can I just chop them...
  9. E

    Controller for Golden Motor Hub?

    Hi: I fried my "cruise controller" from Golden Motor. As I have had for only 10 1/2 months, it should be under warranty but should Golden Motor fail to honor that, I am wondering what my options are. I have the 1000 watt 48V front hub motor with external controller. Are there other brands...
  10. E

    Golden Motor USB controller configuration tool

    Folks: Golden motor has posted the software on their website for free download. They also have a picture that shows the cable and where the various colored wires go. While they want $50 for the cable, it looks like anybody with a pair of dykes and a soldering iron could make their own. Has...
  11. E

    How and where to mount magnetic reed switch for regen brake?

    Works great except for the fact that it is binary: all or nothing. It sure would be nice to have control of how hard it brakes. I have the Golden Motor cruise controller and the brakes slow the bike quickly to the point where the mechanical brakes can stop the bike easily and this was a...
  12. E

    sandwich packs?

    Sorry, I did NOT end up with the Harbor Freight cells
  13. E

    sandwich packs?

    Here is what I ended up with:
  14. E

    How and where to mount magnetic reed switch for regen brake?

    The attached picture shows what I ended up with--perhaps what Rick intended!
  15. E

    How and where to mount magnetic reed switch for regen brake?

    Thanks guys, I'll ponder the brake levers more closely. Maybe I can stick a magnet in the hole for the lead thingy? Or take that spoke magnet and unscrew the magnet from the rest of it and drill (and tap) a narrow deep hole instead of a short fat one? Or just get a momentary toggle switch and...
  16. E

    How and where to mount magnetic reed switch for regen brake?

    Here is a picture: The situation is complicated by the fact that wheel is still not centered. I need to spend another couple of hours with a spoke wrench!
  17. E

    How and where to mount magnetic reed switch for regen brake?

    Hi: I ordered the magnetic reed switch from Rick in the cold Ontario a couple of years ago and am finally remaking my bike with a controller that can take advantage of a switch. In the first build, I just made it so that it was ergonomically impossible to squeeze the brake and turn the...
  18. E

    Golden Motor Regen BLDC 48V controller

    I was so happy when I first read your all's responses to my pictures of my GM controller. The bearings went out on my 36V hub and I replaced it with a 48V GM wheel. I could not get the controller and the wheel to sync up right and did exhaustive tests which lead to the conclusion that the hub...
  19. E

    Inductance of coils

    I visited my local friendly scientific instrument tech and he got out his LRC meter and measured the inductance of the three coils in my 20" 48V front Golden Motor Hub. The units are micro Henries (uH). Between Green and Blue: 578 uH Between Blue and Yellow: 550 uH Between Green and Yellow...
  20. E

    Link to video of Electrobent's test of his wheel

    Hey Guys: I am at wit's end. I can't dial this thing in. Please view my video and tell me what you thing is wrong. Thanks very much! http://www.youtube.com/watch?v=BKRYu4V5A5U
  21. E

    I think I have a miss-wound motor

    http://www.youtube.com/watch?v=BKRYu4V5A5U
  22. E

    I think I have a miss-wound motor

    I am using the Golden Regen Controller. The Hall sensors work No coils are open
  23. E

    I think I have a miss-wound motor

    can you say more of what you mean by "Mis-coordinated"
  24. E

    I think I have a miss-wound motor

    I have a Golden Motor 48V front wheel that I can't seem to dial in. It has no torque once it is on the ground. The Hall Effect Sensors fire No coils are open If I spin the motor as a generator, I get nice pretty sin waves across all 3 pairs of motor power wires. If I disconnect the blue or...
  25. E

    Hall sensor firing order

    I have a 48V Golden Motor front hub that I can't seem to dial in. I tried swapping the yellow and green for both the phase and power wires and it got a little better but it still does not want to start from a stop and needs to be push-started. Built an LED tester and got the following...
Back
Top