• Howdy! we're looking for donations to finish custom knowledgebase software for this forum. Please see our Funding drive thread

Search results

Date Relevance Most replies

  1. smotors

    Votol EM-100 & EM-150 controllers

    ...can be connected to a controller that can work without sensors and check the motor. if the fire was strong, the magnets could be damaged. But they are separated from the body by an air gap, which does not transfer heat well. It can be assumed that the magnets have not lost their quality. At...
  2. smotors

    Votol EM-100 & EM-150 controllers

    ... the question is, can the parameter EBS ratio regulate the recuperation level?
  3. smotors

    Votol EM-100 & EM-150 controllers

    earlier there was already information that it is impossible to leave blank forms.
  4. smotors

    Votol EM-100 & EM-150 controllers

    ...additional connection is not required. There is already a connection inside the controller.
  5. smotors

    Votol EM-100 & EM-150 controllers

    ...it probably is. I had a similar case.
  6. smotors

    Votol EM-100 & EM-150 controllers

    ..look in the window "Display" the state "Fault display", and why in the right additional window You have a check for "reverse" ?
  7. smotors

    Votol EM-100 & EM-150 controllers

    ...the connection between key lock and B+ is it really good?
  8. smotors

    Votol EM-100 & EM-150 controllers

    Thank You. This is important information.
  9. smotors

    Votol EM-100 & EM-150 controllers

    I want to make the correct settings. what do these parameters mean in each window? how do they work?
  10. smotors

    Votol EM-100 & EM-150 controllers

    This can be the Hall angle and the correct connection of the phase and hall wires. You can try changing the alternation.
  11. smotors

    Votol EM-100 & EM-150 controllers

    who knows what this effect is? ..When the engine speed increases, a high frequency sound is emitted at a certain moment. the current immediately increases slightly. When I connected the oscilloscope, I saw a decrease in the PWM frequency from 15 kHz to 8 .. Is this done to improve control at low...
  12. smotors

    Votol EM-100 & EM-150 controllers

    ...to enter the calibration mode, you need to remove 0, and with the key pressed " Shift", press twice " ~ " about regenerative braking. During the tests, did you use a battery or other current source? The battery protection system will not damage it.
  13. smotors

    Votol EM-100 & EM-150 controllers

    Controller setup succeeded). The motor rotates without load stably in all modes. I am glad. There will be more settings when working with the load. Thanks for the help. )
  14. smotors

    Votol EM-100 & EM-150 controllers

    what does this parameter mean? how to set it up correctly?
  15. smotors

    Votol EM-100 & EM-150 controllers

    Thank You. Very useful information for me. The further, the more I learn to configure the controller. :thumb:
  16. smotors

    Votol EM-100 & EM-150 controllers

    ...how do i enable calibration mode: https://youtu.be/MM26C-Gajw0 what actions are wrong and what to do next?
  17. smotors

    Votol EM-100 & EM-150 controllers

    if there is a check, then you can select L M H and S mode. I'm already in calibration mode. in the picture above, at a rotation speed of 4311 rpm, the parameter Q# is 1492. But I was informed earlier that it should be in the range of 100-200.
  18. smotors

    Votol EM-100 & EM-150 controllers

    Something goes wrong with me. When I press the remote control, the motor can rotate the slider on the screen. When you press the calibration, on the third screen for some reason there is no additional window. There is only a temperature window. And when you go to this third screen, the motor...
  19. smotors

    Votol EM-100 & EM-150 controllers

    Thanks for the information I really need. I will do experiments on Friday. :bigthumb:
  20. smotors

    Votol EM-100 & EM-150 controllers

    OK. Please tell me what parameter should I control for stable operation of the motor at high rotation speed? You said earlier that the value should be in the range 100-200 ... what does the button mean " CLR DTC" ?
  21. smotors

    Votol EM-100 & EM-150 controllers

    Thank You. I will do it according to your recommendations. If my result is bad, I will wait for your detailed instructions. Question about port settings. What parameters absolutely cannot be set so as not to block the controller? I'm nervous ... :roll: ...added I have turned on the...
  22. smotors

    Votol EM-100 & EM-150 controllers

    Thank You. I will try to make the settings according to your recommendations. I would be grateful if you could show me how to activate the calibration mode and check the motor timing on the display screen. I've got one more question. I think I made some wrong port settings, because the motor...
  23. smotors

    Votol EM-100 & EM-150 controllers

    HI ! I cannot get the motor to run smoothly at high RPM. There is a knock and then a stop. It looks like a sync failure. I think so. Here is my controller settings. While testing without weakening the field. Who can help me? https://youtu.be/j35A8WuI-ME
  24. smotors

    Votol EM-100 & EM-150 controllers

    This thread is alive. Now more and more users of this product. And, by the way, a good device). But the instruction manual is disgusting. I think that users would like to have detailed, accurate information on each parameter setting item.
  25. smotors

    Votol EM-100 & EM-150 controllers

    Hey guys, This is my first post on this forum ever. I want to use Votol with my homemade motor.The motor is made from a car generator. Installed magnets, Hall sensors with an external rotor. New winding. With a simple controller, the motor works fine. At 80 volts 5500 rpm, current 4.5 amps. But...
Back
Top