Search results

Date Relevance Most replies

  1. N

    XH-18 display with TSDZ2 running OSF - My build

    Hi mate, my bike size is large. With VLCD13 you probably need to flash the display as well.
  2. N

    TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

    Thanks for the response. I guess there is nothing I can do as I don't want to replace it yet.
  3. N

    TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

    Hi mate, thanks for your great work to bring OSF to this amazing conversion kit. Do you have any idea why my XH18 display keeps resetting the odemeter to previous reading? For instance, if I start riding at 4km, after rding 20km, and power off the motor, the next time I power it up, the reading...
  4. N

    TSDZ2 – XH18 Display anti-reflection and water-resistant Tuning

    nice job! does your display reset the odo by itself? Mine does so almost everytime I shut it off and it is very annoy in that I don't know how many kms I have travelled in total.
  5. N

    XH-18 display with TSDZ2 running OSF - My build

    Originally I had a kit with stock controller, new version, so no OSF possible. I bought an old version controller from China and flashed it with OSF, using stock display VLCD5, which worked great. However, the reliability of VLCD5 is questionable, so after a few crashes, the internal spring...
  6. N

    Some tsdz2b can't be flashed?

    OSF is the way to go.
  7. N

    XH18 on Tongsheng hub motor controller

    my problem with XH-18+tsdz2 mid drive controller running OSF is, the odometer resets all the time. Other than that all is good. Any idea?
  8. N

    STlink v2 doesn't connect

    search for it. Measure the voltage across ground and swim, I can't remember whether 5v or 0v means new controller.
  9. N

    STlink v2 doesn't connect

    new version of TSDZ2 controlers have different microcontrollers, so stlink won't connect. I bought an old version controller to run OSF.
  10. N

    Hardware temperature control tsdz2

    All Australian sold TSDZ2s (ebay and etc), if I am not wrong, are new version with new controllers due to legal restrictions, not ST chips anymore. So there is no way to use OSF. I bought an old version controller from China (old stock) and swapped it in. Now I am running OSF with VLCD5, which...
  11. N

    Some tsdz2b can't be flashed?

    new versions use XMC1302 chip instead of STM32.
  12. N

    TSDZ2 48v 2020 new firmware

    thanks. Will get the j-link. But how the firmware is modified to remove the speed limit?
  13. N

    Some tsdz2b can't be flashed?

    Thanks, that is too bad, it measures 0v on my controller:
  14. N

    TSDZ2 48v 2020 new firmware

    Hey mate, how did you do it? Edit the hex?
  15. N

    TSDZ2 48v 2020 new firmware

    Looks like opensource firmware for tsdz2 version 2 is a dead end now? Hmm, maybe the best is to source a old version controller from China or somewhere else?
  16. N

    Some tsdz2b can't be flashed?

    I have seen somewhere people saying that there is a version of tsdz2b firmware can't be flashed. I have tried two ST-link, both of which are clone, but one is used successfully on a 3d printer. I am suspecting that my tsdz2b can't be flashed. Is there a way around this? Thanks in advance.
  17. N

    Is kt36 controller safe with 48v battey

    yes. Display usually set up the controller. I hope by sensing the voltage, the display will set up the controller accordingly.
  18. N

    Do I have to build OSF with VLCD5(stock display) myself?

    Thanks guys. Will follow the instructions.
  19. N

    Is kt36 controller safe with 48v battey

    Yeah. I think the LCD5 detects the voltage and set up the controller accordingly. But anyway, I can read the voltage on the display to see if it falls too low. Thanks for your help!
  20. N

    STlink v2 doesn't connect

    It looks fine. All drivers installed and I can see it in the device management. I have also made the cables very short. However it alwasy says so: (API) ERROR : Cannot communicate with the device ! Check the SWIM cable connection and check all the needed pin connections on the SWIM connector...
  21. N

    Is kt36 controller safe with 48v battey

    As Docw009 said here, I believe that the KT LCD5 manual does say that it sense the voltage therefore LVC is not an issue but the component voltage limit is realy a concern.
  22. N

    Is kt36 controller safe with 48v battey

    Thank you very much. I will open it to see if it 50v or 63v.
  23. N

    Do I have to build OSF with VLCD5(stock display) myself?

    I have searched everywhere but I can only see OSF source code. Building it is possble but can someone upload a hex file to make life easier? Or we have to build it ourselves to customize things? Sorry, this might be a simple question but I spent too much time searchng and it leads nowhere.
  24. N

    Is kt36 controller safe with 48v battey

    Hi guys, Tried searching but no results. Is it safe to do so? My ebike is 36v 350w hub drive with kt36zwsr controller and kt-lcd5 display. Now I have a 48v 15ah battery and want to mix batteries. It appears that kt-lcd5 can sense the voltage but I am not sure. Thanks in advance.
  25. N

    Hardware temperature control tsdz2

    Any pictures mate? I bought the same flat 25mmx1m aluminum bar from Bunnings and made an insert to use between the top of motor and the housing: But not sure what is the best way to wrap it around the motor body. Thanks in advance.
Back
Top