Search results

Date Relevance Most replies

  1. T

    uggh! another noob needs help :-)

    good news update: I placed my hall sensors and phase wires back in the normal color coded combinations and decided I would unplug my throttle cable from the controller. I moved the crank with the PAS still connected and the motor spun up nice I placed my foot under the tire and the motor...
  2. T

    uggh! another noob needs help :-)

    John, it sounds as I have frustrated you. My intention was not to waste your time I have read and re-read your advise and followed it to the best of my limited understanding on BLDC motor tuning. I tried everything you said and ran out of possible hall/phase wire combinations. So I moved on to...
  3. T

    uggh! another noob needs help :-)

    Guess who tried to test the suggested https://endless-sphere.com/w/index.php/%20...%20less_Motor - This guy The guide says "crossbreaks hall sensor and phase wiring spreadsheet for tying most of the 36 possible combinations" please tell me that there are actually more than 36? cause I tried...
  4. T

    uggh! another noob needs help :-)

    John in CR, thanks you for your clarification and guidance. I will test the various combos tonight and see if I can right the timing. Hallomotor is finally going to ship me a replacement controller so in 2-3 weeks I should be able to swap that out and see if the new controller works. In the mean...
  5. T

    uggh! another noob needs help :-)

    John in CR, thanks for jumping in... I reviewed a lot of your posts and you mention the false positive often and provide similar instructions. could you please be a little more detailed in helping me right the "false positive" your instructions are vague to the novice (me) that is not...
  6. T

    uggh! another noob needs help :-)

    Hi DAND214, thanks for your reply the 10+ amps reading was taken as a peak of multiple attempts to get the wheel to spin up with load Trying to actually ride and having the motor stall numerous times. The test results I just posted included turning the power analyzer off and on between each...
  7. T

    uggh! another noob needs help :-)

    here is some data from the power analyzer starting battery voltage = 53.75, power on at throttle causes .03a draw, LCD on causes .13a draw no sag on Battery voltage positive and ground connection on hall sensor shows 4.38v With the wheel lifted (0 friction) tests were completed at 10, 20, 30...
  8. T

    uggh! another noob needs help :-)

    Aroundqube thanks for the link. I will try switching phase wires around and testing tomorrow, (just to be confident before I go switching wires around) my wheel does spin in the right direction when I lift it off the ground at 46 MPH on the speedo. the problem is when I set the tire on the...
  9. T

    uggh! another noob needs help :-)

    Lurkin here is a picture of the controller. and for what it is worth what is a speed sensor seeing as I don't have one?
  10. T

    uggh! another noob needs help :-)

    Ykick I tested the mosFETs and they appear to test good according to the troubleshooting link you sent me. I have 9.85 green, 9.82 blue, 9.90 kOhms on the ground tests and infinite resistance on each for the positive test. thanks for the link I used that same page to test the throttle, and hall...
  11. T

    uggh! another noob needs help :-)

    I did not test the mosFETs in the controller yet, I don't know the process to test the mosFETs. This is a new kit and I was hoping I would not have to crack open the controller, if I have to return the whole kit for a refund I don't want to void any warranty by doing so. what do you mean by...
  12. T

    uggh! another noob needs help :-)

    Hi I have been reading the forums on this site for about 2 months while attempting to build my first bike. please excuse me if I have missed one of the posts that already addresses my problem but I have yet to find answers to my problems. I built my battery pack over the past 6 weeks from...
Back
Top