Recent content by ColdRider

i have bought the satiator 7205 , planned to charge my 21S PWR pack , about that 3rd wire on the charging lead could i use it to monitor the Pwr pack temp as it is charging ? is there anything else it can be used for ? My BMS is an ANT with BT Android App , i have not powered it up ( the BMS )...

Allo hall of you votol user's I am looking into getting me a new controller for my Cyclone 3K since i am about to build my new battery set ; Planned for a 21s using INR-21700-P42A cells ,two packs for less V Sag overall ,any way here is my ? ; My BMS's (each pack has one ) ANT 120A capable...

Grats Dtm1087 very nice build with in great cost to and yeah your bike is gonna break parts sooner than later , Mine did I slowly replaced EVERYTHING exept for the frame and handlebars all upgraded to medium quality parts. hmm about your throttle what you using ? I been using a wuxing...

To Squeeze : I see you have a thumb throttle like I have ,can you tell me (maybe a picture ) what the wiring I have is ,the throttle has 6wire (Red/Blk/Whit ) they make the throttle work and the other 3 are Brown + (Green + Yellow) together . My question is the Green + Yellow pair they...

To Squeeze 3 speed connector on stock controller - with nothing plugged into that connector, what's the max rpm of the motor using a 52V battery? I measured with a digital rpm laser thingy and with a 52V fully loaded (58.Ish V ) output shaft RPM was 665 - 650 rpm hope that's info...

about a temp sensor in the cyclone I got me a grin tech motor cable with two extra wire http://www.ebikes.ca/shop/electric-bicycle-parts/wiring-accessories/grinmotorcable.html for the temp http://www.ebikes.ca/thermistor10k.html to hook up to CA.V3 So I asked earlier how complex can it be...

That is true but what connects to : So what connects to this part #2 is where I am lost ,Ignition has to be one of the two ...What connects to (Gr/Y) ? What connects to Brown ? From the controller side ,using...

Last I looked Luna he did not have it anymore on the website ,but it was an option when buying from original cyclone batch Its not the Oro Throttle,What I have is this wuxing ,as many as I can find they have different wire colors and so i'm not willing to see it puff out white smoke ...

Thank you Minimum for that info :D Now if I could get the picture or the wiring info on the thumb throttle ,what I know is : #1 : The thumb throttle has six (6) wire and Red/White/Black are +5v/Signal/Gnd ,those are no issue #2 : Then there is Yellow/Green/Brown theses are (what I have...

Allo Every Cyclone Rider :D Would one be helpful and post or message me a picture of the connection from the cyclone thumb throttle (the one Luna was sending with the original first cyclone batch) and the controller ,I modded it and should have taken a picture of it b4 .Now I need to know...

Curiosity killed the cat ? aint gonna kill me ! I got SBP new freewheels , and out of curiosity I opened the (unscrewed the ring side of crank freewheel ) ,Now i'm stuck :oops: it wont screw back on .It locks up with a bit more that 1/8" to complete closure . Is anyone with some trick...

That's great tool and works well too Thanks Spinningmagnet ,Here is a tool I did use many times it may lack extreme precision but has served me well over time ,I find it long to fill in but that is what a Hobbyist/Enthousiast DIY E-Biker want at least thats what I got ->Fun :D ->...

Water In The Cyclone Motor :Question : How can I seal the back of the motor ,where we see the shaft ,Robocam posted a pic about water damage .I am trying to figure how to waterproof that entry point ,being in plain sight & a bearing .15-16mm ID I am looking in plumming stuff they may have...

NP Robocam ,with what you typed it made me flash on the solution somehow . AND-> about the liquid tape :The cable entry on the motor I did apply 3 coats all around it ,On the 1st application I pulled in the opposite direction the cable to have the LT(Liquide tape) enter deeply .Second & 3rd...

Being lazy here & copying my own post from another tread :Solved =D CA V3 Works fine . To Resume my mistakes & solutions in the hope that it will help some one els : 1) Make sure that the pinouts of your Throttles connectors & CA are the same I solved this one by adding a exta Throttle...