Recent content by Dirkro

My first try would be: Disconnect the batteries, swich on for discharging the system, replug batteries , swich on and dont touch the pedals for 5 seconds. Second, please check Motor ands Batterie parameters in the setup, Try to make a test drive with a few minutes with a intermediate...

Found it :-) For people who dont find: It is behind the highest support mode (9 in standard config) For me 9-10 is the best value for E-MTB sensivity.

Sorry, then I have some questions with the modes: Should I only enable one mode in the configuration? If so, what will happen if I will enable two different modes? If not, How to change from mainscreen? I did not find the method to swich! Regarding MTB Mode: just to ned to put on the...

I installed 0.20Beta1 Yesterday from Github Did cadence sensor calibration / advance mode during setup, My cadence is shown OK, a little bit flickering up and down ( +/- 2) Was working fine on first test drive, working very smooth and nice! Was a little confused by the changed...

I am not good in programming but I found following formular: 95.5 * (1/0.637) = 150 ... Shouldn't it be 95.5*0.637=60.8 instead , (I rounded from 0.637 to 0.5 , *100 , so find good corelation then ?

Sorry, in my opinion, by doing these tests, you add a lot of uncertain factors: weight, steepness of road, speed, lost in the drive, lost of tires. Î did mesurments with a analog torque wrench, diretly on the axle . they where good repeatable would guess 10% error, see below. When...

For me this is the only reliable way to calculate the expected range while riding. I have a battery with a quite high resistance (> 200 mOhm ) When I look at the current while I am standing still after a ride it is slowly going up during the first one or two in the range of 0.4V My...

Hi, if you mean the backwards (forward) counting of the battery mW , then I can say that I am a fan of this feature and I use it regulary! For me one of the highlights :-)

Yes,you are right There might be a bug in the calculation!! In my setup, at a cadence of maybe 90 it takes about (feeling) 20 Seconds to climnb from 70 to 89. Zero is reached in one second , when stoping pedealing, when I start agaín (feels like 80 to 85) it is starting with 50,then...

Hi, I made mesurments with input by an old style analog torque wrench and the values shown at menue 9.2 Input Value 9.2 0 Nm 50 10 Nm 60 20 Nm 69 30 Nm 78 40 Nm 91 50 Nm (98) maybe not fuly correct I hope this helps to improve the calculation of...

I think the function is implemented in the setup menue under item 7.2 Curent ramp up per second . Standard is 5, can be set up to 10. I would like to set it up to 12-15 if you ask me.

Hi, I have installed 19.8 on 36V motor and battrie Thank you for this!!! - I like the new button logic. - The change from road mode to offroad mode I cannot real understand, because it is not logical to for me to swich to road mode through a button code. It is running well in my opinion...

I like to have a good torque with low candence too, to pass crossings and pass mud holes you dont expect. Then I start below 50 cadence and enjoy / need the power. Just my two cents

Hi, I had some requests regarding error blinking 1 and I have asked ho to make it better for me, because I sometimes got stucked on steep sections. But frankly spoke, I just swiched off the setting to power on without pedal rotation and I was suprized how fast the power came in the...

Today happend again in the woods, Want to start a climb after pusing the bike, I was two times not fast enough to turn the pedal when going onto the bike (not usng brakes). Please tell me where is the code for this? , maybe have to fork to make tests if it is possible to make a "min...