Recent content by HomeScape

21700's are way more expensive and are far off from worth it with the info i've gotten so far. For example these are 7,25 euros: IMR21700 5000mAh - 10A Side note; i think i'd have to pay import tax if i'd order from the website you listed, so i doubt that its cheaper for me.

21700's are way more expensive and are far off from worth it with the info i've gotten so far. For example these are 7,25 euros: IMR21700 5000mAh - 10A Side note; i think i'd have to pay import tax if i'd order from the website you listed, so i doubt that its cheaper for me.

I have never worked with 21700's but i'll look into it. Thanks for the links to the cheaper sites, saves me some cash if i were to make another one. Tim

I personaly dont think that fixing the motor is worth your time, a 408w motor isn't anything that would cost a lot to replace with a new one. I wouldent want to risk a broken motor halfway to my work... Tim

I think all cells would be put under equal load, so i'd need another (150-64=86A) 84A in battery of the same kind if im correct. I think if the type of cell is different then the discharge is different aswell and the packs would be unbalanced quikly. That would mean i need (84/6.4) another 13...

Options so far: Samsung INR18650-30Q 3000mAh - 15A 15A discharge rate, which would be fine at the year of useage, but after 250 cycles the capacity (and max current?) drops to 60% These cells are 3,40 euro when buying 200 Other option, more expensive but maybe better? Sony Konion US18650VTC6...

Hey everyone, I've owned a 1000w 48v bike for over 2 years now. I made 2 packs of cells myself for this, 13S6P * 2 in paralel. I recently bought myself a sabvoton controller, 72150 (72v, 150A) so i needed a new battery pack to supply the voltage. I didn't really think everything through and...

Hey thanks for the info! I'm running a 5000w motor from C & N (aliexpress). I'm planning to buy the whole kit from the seller and he's paying for import, so buying from Chris would most likely be more expensive for me at this point.. I'm not planning on jumping a lot, i'd just feel safer with a...

Are you sure that your min throttle is set correctly in the sabvoton settings? I remember from my controller that my throttle sometimes gave ~2 volts at the start, my min throttle was set to 1.5v or so. The controller would then jump in error mode on startup to avoid the bike shooting away by...

Aight goodluck :)

Did you apply 5 volts on the hall sensor red wire yourself to test them? Either way if the controller is active it should output 5 volts on the red hall sensor wire.. You could try to connect the green or blue wire to black to set it into high or low speed. I'm not aware that this is...

Give me a moment to look at that into detail; i've found this one laying around maybe you can relate to some of it: https://i.imgur.com/oLtU49K.jpg At the very top you can see the thin red wire, this is the ignition (connect to red positive) Then second the blue/white, i dont know, could be...

What exacly do you mean by the extra wire comming from the battery positive? Is there an extra small red wire comming out of the controller? Based on what do you believe the controller is now active? -> The hall sensors shouldent be the problem at this point - if they're configured in a wrong...

I might be a little late to the party but i would like to add that your motor isn't the issue here. A 1500w motor might aswell be a 1000 or a 2000W motor. You can technicly pump any current trough any motor. The smaller ones just heat up quick and burn down. I'd suggest a controller without...

I love this frame and i'm very intrested in buying one. I have a couple concerns though; maybe you guys can help me out? The front fork isn't pre-installed, i've never done this and i have no clue how this is done. Can this be done with some simple tools and do i need a specific combination of...