Recent content by oded

  1. O

    Outrunner for a lightweight conversion (Oset 24)

    We did convert the bike to brushless, turned out very well - https://www.facebook.com/groups/643915049618116/permalink/925464301463188/
  2. O

    motor current vs. battery current & duty cycle

    Thanks! what I am getting to is what will be the best duty cycle parameters for slow technical hard enduro? steep rock climbs at low speed. don't really care about speed & fast riding. should I leave the duty cycle parameters to 0.5% - 95% (this is the default)?
  3. O

    motor current vs. battery current & duty cycle

    analysing the last trip via the VESC tool, I see that most of the time the motor (Phase) current is 3, or 4 times higher than the battery current (can be seen clearly in the attached screenshot). when climbing steep hills. the motor current is very high (over 150 amps) while the battery's...
  4. O

    replace melted phase wires - need advice

    I think it's a misunderstanding. I don't use a 9 tooth connector. only the wires are warm. conccections are fine.
  5. O

    Cutting phase wires?

    How did it turn out? Sent from my LM-G850 using Tapatalk
  6. O

    replace melted phase wires - need advice

    OK. Thanks for the clarification The wires are melting along their entire length. Connections are fine, and motor is cool. So, they need to be replaced. Just hope it won't be too much of a problem, digging inside the motor. Sent from my LM-G850 using Tapatalk
  7. O

    replace melted phase wires - need advice

    Thanks. the wires are bundled together in a jacket. their width is extremely small for the current they suppose to deliver - I am guessing 16 gauge, so no wonder they melt. they need to be replaced, no question. I am just wondering if replacing the outer portion of the wires only (I mean after...
  8. O

    replace melted phase wires - need advice

    the Golden Motor 108 1.5kw that I am using have very small diameter phase wires (16-18 gauge). the motor is capable of up to 80 amps, and remains cool, but the phase wires melted after 10 minutes. I'll try to replace them with thicker wires, but if opening the motor turns out to be too...
  9. O

    Greentime controllers

    are older & better quality Greentime controllers still available somewhere? any other chinese brand that is available now produce a worthy controller?
  10. O

    Bypass LCD display

    Made some digging, and it's a simple 790 display unit (not lcd). So, I guess red to blue is what I need to short. Sent from my LM-G850 using Tapatalk
  11. O

    Bypass LCD display

    I think you are right, but can't confirm that. Sent from my LM-G850 using Tapatalk
  12. O

    Bypass LCD display

    If I knew life would be so much easier. I don't know, hence the question. Received the controller without the display. Sent from my LM-G850 using Tapatalk
  13. O

    Bypass LCD display

    got a used controller for my 48v rig. don't have the display that came with it, but it only showed parameters like speed and voltage. no power button. from the controller there are 4 wires that goes to the display - red, black, blue & green. measuring voltage shows 50v between the red/black...
  14. O

    Golden motor 108 compatibility?

    Front 9t sprocket Rear 102t sprocket 24' tire Upgraded an Oset 24 to brushless Sent from my LM-G850 using Tapatalk
  15. O

    Golden motor 108 compatibility?

    Installed a 1.5KW Golden motor (model 108) https://goldenmotor.bike/product/1500w-bldc-motor/in a home built 48V rig. tried 2 Votols (EM50S & EM150), and a Kelly KLS 7218N, but can not make these combos sync. free spinning on a jack, works great, but once under load, the motor is cogging &...
See more
Back
Top