Recent content by Sinhu

I like the design on the MX60, and just got one a bit run down but at a nice price. At first sight, not bad. After going it over the scooter had mores issues then i first i thougt, i love the battery solution but it need to be rebuild. It holds 60,4V fully charged so thsts cost. And after...

Thank you :) As a starting point for a ebike build you can’t do any better then a Stromer frame, it’s just solid and well buildt with high quality parts. As the motor are from TDCM i’m looking forward to finaly try it :) Stromer has as all the major brands gone for Can-bus and elektronic...

Well usually find them on www.finn.no This is a thru axl motor and no orignal torque arm or anywhere to mount one :( So i have to try a homemade version :)

If you are a Stromer owner in Norway, and have a problem with your bike you are in trouble. Ad there’s no longer a Stromer dealership or partner in Norway you have no where to go. If you contact Stromer ch they just ask you to contact your nearest dealership (in my case is in Denmark and 800km...

Hi ! A new project pop’t up :) As i live in Norway where a couple of Stromer dealership’s as come and gone. At the moment it’s posible to pick up these bikes at a very reasonable price if they got a problem. Stromer, if you contact them ask you to go to the nearest dealership thats in...

It’s tru thats a bit of work, if you don’t have some parts laying around it would be a bit expensive to. But one thing is serten, switching to hydraulic breaks and do the suspension makes all the difference too this cool little scooter :)

Hi ! Not sure if i understand what info you want ? Do you mean the EB-bus cable too the controller or the wirirng inside the mortor ?

Hi ! I found a beat’n up ww i paid €50 for and decided to make it the project this winter. Starting with taken the scooter completly apart, and the list of parts needed became long :( New main controller Left side rear rim 1 new tire Headset bearings Plastic wheelside cover Break disc Down...

Sorry about the late replay, the Stromer project was at a stand still untill october. You don’t need to buy a bb torque sensor, just use the orginal Stromer TMM torque sensor it works like a charm. If you use a CycleAnalyst v3 from Grin, you can hook up pas, torque, switches, trottle and...

At last the Stromer is finished !!! 😤😤 It’s now a bit overkill of a bike, running the Phaserunner at a 50amp max i needed to ad a heatsink. The Crystalyte H55100 motor has never been above 38c, it’s a bit on the heavy side but runs smooth as silk with lot of torque. But it has become a...

Got the frame and bike as scrap metal, with a hope of building it back up. More then enough room in the frame to build a custom battery pack. Easy 14s5p. But the frame and rear drop out is gone, the only useful thing was the Rock shox bluto. It has a wired backframe 135mm lased of centre on...

Hi ! Just got a Polaris Sabre EV506 and never seen this motor before. Integratet controller as Stromer still uses. Have to open it and see what can be done : Rock shox bluto have some scratches but still in good shape. Inside it is a standar DD hub

The Stromer setup with the controller inside the hub had to be restricted to 36v i belive, heat from the motor and controller all in the center :) Planing to use 52v, and as of now that i’m going to use a Phaserunner i will set a limit to 50A. As this are the P48 version it’s not as torque’e...

It’s thight but i hope i will get it thru :) Stromer has 3 connectors going in to the hub, 5pin conector to the display, 3 pin to the tmm sensor and battery power + 1 signal from bms It has 5mm gap at the most I think i will try to gently heat an try to shape the L10 a bit. Will give a...

New update on the building process. Had too start wiering all over again, this time using new julet conectors,5pin for phase signal and a 2 pin for temp, and XT150 for phase wires ( it’s overkill, but thats the conectors i got :) Got a respond from Grin today, telling me to not use trottle...