Search results

Date Relevance Most replies

  1. O

    BAC855 controller + Crystalyte HT 3525 motor

    Hello, Have you made motor discovery procedure for calibration? Have you set the correct input for throttle ?
  2. O

    SOLD - CYC battery case X-36 X-52 X-52L - EU or US

    Send PM
  3. O

    TSDZ2 250w 36v with 500C Display instead VLCD5

    Hi, I have a TSDZ2 250w 36v motor with VLCD5 Display and Throtle. Everything works well. I bought a 500C display with new cable and Throttle, but i have 2 Issues : 1/ Activate taillight on Display don't activate the light, was Ok on VLCD5 display 2/ When using Throttle, i have a speed...
  4. O

    MAC motor parts

    Hello, i'm interested by your Mac Motor. Can you confirms 8T, 10T, 12T ? Regards
  5. O

    PAS on Adaptto Controller

    Hello, i have an Adaptto Midi controller, with a PAS connector. Do you know how it's works ? Is there any relationship between Pas rotation rate and Power/Throttle, or is it only on/off ? I not found any documentation except plug information. THere is nothing in the setup menus. Thanks. Olivier
  6. O

    64v BBSHD Bac855 or Phaserunner?

    If you use CycleAnalyst V3.1, throttle, brake sensor, speed sensor, PAS goes directly to the CycleAnalyst.
  7. O

    64v BBSHD Bac855 or Phaserunner?

    Hello, PhaseRunner has been design to be simple to use. Grin Software is easy to use and to understand for programation. PhaseRunner has been design from BAC 850, with some improvments. BAC 855 is much more complicated, as all features/options are avail to the customer, ... if he need them ...
  8. O

    BUILD/HELP ME - BBSHD to ASI855 wiring harness

    Hello, Be very carefull and check twice your connections to the display ! You have to know that Bafang connections plug or ERT or ASI mode are differents , and you can break your display or controller with wrong signal between controller and display. i break 1 Bafang controller and 2...
  9. O

    ASI BAC 855 Factory Reset

    Hello, i have an ASI BAC 855 Controller from E.R.T, and i'm not happy with the display. So i want to reset the controller to factory, to use it as "normal" controller. Do you know how to Reset Factory an "locked" E.R.T ASI Controller ? Kind regards.
  10. O

    GNG / CYC X1 Pro 3000w

    Hello, i made some tests with this PAS E-Rider with a Cycle Analyst 3, and you have to know that you cannot use Torque Sensor to start motor from stop. You can adjust torque parameter to have a motor reacting as you wish, but it's not possible to start from stop ! I ask question to Justin from...
  11. O

    What are the advantages of buying dicount motorcyle helmets

    Look at Tektro Auriga Twin. Olivier
  12. O

    Nucular electronics - complete kit for ev!

    hello Vasilisk, I have Cyc X1 Pro Gen 2 with original controller FOC (i suppose) with 20s battery/28Ah/80A BMS. Do you think that i will have better efficiency/performance with the 12F controller ? Also, do you think that i can reduce noise with your controller ? Kind regards. Olivier
  13. O

    Nucular electronics - complete kit for ev!

    Hello Vasilisk, My 12F controller arrived at my post office last Friday, but be able to pick up only this morning. Many thanks. Olivier
  14. O

    Nucular electronics - complete kit for ev!

    Hello, Some good news about shipping delayed in Russia, 17track shows that my parcel just leaves Russia to my country (France) yesterday. Hope the same for others parcels. Olivier
  15. O

    Adaptto Midi-E overheating problems?

    For information. On some of my Adaptto controllers, accélération was too smooth, even after many calibrations. I discover that Adaptto changed mosfets thermal sensor at a date, from KT83 to KT84 (from memory). If you have the wrong thermal sensor on the setup, (after firmware update for...
  16. O

    N.E.S.E. the no solder module

    Hello Agniusm, Does hardware (hardware set, printed modules 6p) are avail for a 6p20s ? It still expecting to ship on 21.11.2017 on your website ! Regards
  17. O

    Adaptto Mini-E/Max-E Owner's Thread

    Hi, i have a 2WD configuration with 2 mini-E (Same firmware revision), with Slaved MXUS Geared on rear, and Master NC 2605 direct-Drive on Front. Everything works well, Master drive Slave, but there is a problem with Speed limitation on Slave. When Setting-Up the Slave controller (Display on...
Back
Top