Recent content by Klauts

hey y'all my haul sensors on my Bafang G62 fried and apparently they aren't replaceable on this motor Soooo I'm desperately trying to find a sensorless controller I can swap in to continue getting some use from the motor. any recommendations would be greatly appreciated, I can't seem to find...

I mean I deconstructed all series connections in the initial 2s10p packs so I was left with 14 1s10p packs and then tested the resting voltage and resistance of each 1s10p group. Then I charged each parallel group and monitored and noted the charge rates of each. Initial charge rate was the...

I haven't been skimping on any components price wise as I've got a healthy fear of house fires (lived through 3 in 31 years....) I got the highest quality BMS in my budget and tested each cell three times before I even thought about connecting them in series (parallels were already made...)...

C$ 45.47 38%OFF | Daly Smart BMS LiFePo4 16S 48V BMS 3S 12V 8S 12S 24S 12V 24V 36V 60V 30A 60A 80A 100A 150A 200A 250A 300A 500A Li-Ion Battery https://a.aliexpress.com/_mqGm4Ts This is the BMS I'm using, I spent the money for one that was full featured and could handle my needs. You seem to...

No problem! Sorry if I sounded snippy 😅 I'm going through some crazy life stuff. Breakup/moving cross country with me dog in 6 days. Didn't mean to be harsh, not normally so standoffish. You've been incredibly helpful seem like a genuinely kind human; I really feel bad about how I went about that...

"As I'm pretty sure has been previously noted in one thread or another for this pack / project, if the cells didn't start out the same, they won't ever be the same; their properties and characteristics are different from each other and will always get worse over time, never better." You are...

My Monstrous Beast™️(14S10P, 140 Samsung 18650 26j cells) pack is back in actions and sufficiently reinforced and shrink wrapped I do believe. Now I'm trying to get the settings on my Daly Smart BMS dialed. I can set the active balancing current anywhere from 0.050ma to 1a and it can be set...

Im sorry to dredge up an old thread but this seems like exactly the information I need 😅 Amberwolf I did the unthinkable and let two wires of different voltages resolve their differences 🤣😅 I apparently missed reinforcing a spot on one of my balance wires and it shorted on the main positive...

Is there any harm to running it without a speed sensor and are they easily replaced?

No but the wiring was damaged, I repaired the wires and re-insulated but there's a good chance it shorted the sensor. Haven't used the motor since then. Put on my replacement after making sure it still spun and forgot about it

The motor has a speed sensor built-in this is a new problem. I'm assuming that means the sensor is fault then?

To further add to the conundrum.... The LCD randomly started showing my speed under load 15km into my ride... Still no speed displayed when no load applied...

Hey everyone, I'm getting seriously fed up with the KTLCD and it's random glitches and automatic power down feature... I've been trying to find an alternative that will be compatible with a KT controller and I'm having no luck... Failing that is there any way to run the bike without an LCD? The...

So ok the way to work today I noticed that my speedometer was only tracking speed if I was either pedaling or engaging the throttle. As soon as no load was applied to the system the speedometer would drop to 0km/h regardless of actual speed. Didn't think much of it... Powered up the bike to...

Woah!!! I looked up the spec sheet and apparently it can handle 1000w 🤣 I just hooked it up and my top speed is now 45km/h instead of 35km/h 🤯🤯 Apparently this motor is even more powerful than my 750W greenpedel motor if the voltage is high enough... Or maybe it's the switch to a sinewave...