Recent content by Bonvin

Hi. What are the working temperatures of the Cycle Analyst V3.1 and the BaseRunner V4 ? I have consulted the operations manuals and there is no reference to working temperatures and/or storage temperatures. I'm actually more concerned about low temperatures. Do you have these informations, do...

Hi. The Baserunner has 4 holes lined along the heathsink. Do you know the caliber of bolts to use? Thanks in advance Gillis

Hi. I want to test my 15 amp Crystalyte controller . Probably that I have a thermal runaway with one phase, to find wich one, I need to put a load to replace the Nine Continent hub motor. Can I build this dummy load with only 3 resistors in a Y or Delta configuration? I did a search on...

Hi. I would like identify a Nine Continent motor. On the side i can read the following number: jz36v500w100614049 Is this a 2805 or 2806 ? What would be the resistance between two pin at the phase connector ? Thanks in advance. Gillis

Hi I am trying a new 36-48V 25A Sensorless Crystalyte Controller that is directly compatible with the Cycle Analyst that drive a 9C motor. To my knowledge the controller is working correctly, but all of those values( Ah, Wh/Km, A, and the W) appears as negatives values ! And the Cycle Analyst...

Hi It's regarding my 25A Infineon Brushless Motor Controller (August 2010). From today the consumption read by my Cycle Analyst in Wh/Km have increased by about 25% Normally the controller is cold and now it stay abnormally hot. To my big surprise the controller become hot even when i...

Hi Can you help me to find a small Hitch Ball and his coupler for my trailer, not the one that is used for the car because they are to big for my need. Some time i find a small hitch ball, but not the coupler ? The hitch ball will give to me all the freedom that is needed. Thanks in advance...

Hi I have read with great interest your "Opening a hub motor - FAQ" I have a 9C rear hub but on a 20" wheel. I have 4009 Km on this hub and love it :) In your FAQ you have remove the wire side cover I will like to know if it's possible to do the same thing, for the other cover, on my rear...

Hi This is my first summer with my ebike and i can read 2504 miles on my CA. It work well for now. How many miles i will be able to do with my rear hub, 5000, 10000, 15000 miles ? I will be able to do the same millage, the next summer with this hub ? Do i have to change the bearing after...

Hi I will like to know if there's a way to make a hole, a small one of about 1.5 inch without removing the motor cover. I must be sure that i will not drop any metal particles into the engine ! It's just for ventilating the motor, for removing any condensation. I dont feel comfortable with...

With the time i find the freewheel noise, more irritating :( It is probably defective and i want to replace it with a 5 speeds low noise freewheel. This one must be compatible with my 9C 2805 hub. You have a suggestion ? Thanks in advance Gillis

Hi. I will like to use the Schwalbe Big Apple 20 x 2.00 tire on my 20 inch 9C 2805 rear hub. I have read that the tire is a little bit wide for the rim, but that it's possible ! Have you try it ? Do you use a Big Apple tire on your 9C. Thanks in advance. Gillis from Montreal

Hum It's a lot more complicated than expected to remove this axle ! My problem is that the nine continent rear hub is 7 mm too wide for my trike. $%#&%$ There is a way to remove 7 mm to the rear hub in a way that it will fit the trike ? It's why i want to know how the axle is made. I...

Hi everybody. I need your help here. I have a nine continent rear hub and i whant to know if it's possible to remove and reinstall this axle. Do i need special tool(s) for doing that. This can be done easily ? I have at least the tool for removing the freewell ! Do you know where i can...

Yes you have the same problemes than Joe ! The BMS is faster than the CA at detecting an overcurrent. I am not shure how the CA is limitting the current. Probably by lowering the throttle? Hum, from what i can read it's not the way to go ! It would be funny to be able to reprogram the converter...