Search results

Date Relevance Most replies

  1. E

    Hub axle

    I was thinking that. I have a lathe so I'd give it a go. I've modified mine so it can take a 5mm skewer for a QR as my frame doesn't have dropouts
  2. E

    Hub axle

    Morning everyone Just thinking about spare parts should anything go wrong plus about stories you read. I did read a story of a couple of people who have had broken axles. With the generic rear hub motor are all the axles the same or do you have to get in contact with the supplier? If so wheres...
  3. E

    Pas issue

    Thanks for the reply. I’ve tried the continuity test and it seems it’s broken. Can I just buy any 3 pin one to replace the one I have? Connection is a 3 pin black red and a colour
  4. E

    Pas issue

    Hi guys. Now that I’ve got my wheel working again with new halls my pedal assist has stopped working (it has been working previously). Can they blow? I think I might have plugged mine back in whilst the battery and controller were turned on. If that is the issue are the ones on the net all...
  5. E

    It’s alive

    Hey. The controller does have a gasket on it but still not sure how much it will be protected. I have some sikaflex sealant coming so might put some of that on it. The connections that came with it are total rubbish. I’ve put an xt90 on for the power cable but the rest will need changing out in...
  6. E

    It’s alive

    All mine are used parts From eBay. Apart from the battery and motor. Think this cost me £700ish and going to use it to save me £200 a month on diesel getting to work. Should be fun
  7. E

    It’s alive

    The wires definitely need a tidy up. I just wanted to get out and ride it. It’s definitely fast. LOVE IT!!
  8. E

    Your Creation's Before & After Pics

    Hi guys. Finally got my bike done. Still need to sort out the wires but that’s not to tricky. It’s a trek fuel x9 2010. 1000w motor. Had to modify the rear axle which I’m going to make a better one at a later date
  9. E

    It’s alive

    Here are the pics
  10. E

    It’s alive

    Thanks for all the info on getting my bike to work again. It was the halls. I also did a rewire. All running sweet. Just need some inspiration on where to put or run my cables and also if anyone knows anything about instructions on the lcd screen I have. I’ll get a picture of the bike later...
  11. E

    Hall sensor confusion

    Many thanks guys. I re wired the broken hall cables where the cables got damaged. I also tested for continuity. I did run a test with the phase wires too which was part of the guild that someone posted. Definitely going to get a tester. Didn’t realise they were so cheap
  12. E

    Changing switch brake levers to magnetic hydraulic sensors

    I’ve been reading a lot about whether to use them or not. When took it out for a test ride using throttle was ok but with the pas it still carries on until it figures out you’ve stopped peddling. Just wanna be a safe as possible really
  13. E

    Hall sensor confusion

    I put it all back together again last night checked and rechecked before I put it all in. Once it was all plugged in I did the rest again with turning the wheel. Yellow wire was on off but the blue and green just stayed on
  14. E

    Hall sensor confusion

    A tester would be so much quicker. Might even look for one now and see how much they are. I need to rewire my halls anyway. The cable is now to short
  15. E

    Changing switch brake levers to magnetic hydraulic sensors

    This is the switch which came with my kit. Thing is I have hydraulic levers which I could modify the switch but it might look a bit bulky. Or I have seen the magnet sensor style which look better. If I wanted to can these be retrofitted?
  16. E

    Hall sensor confusion

    I’ve ordered 6 as like I said before I have different sensors in them. It probably doesn’t make a difference I just like things to be the same. Thanks for the advice
  17. E

    Wooden sticks

    Trust me. I see some shoddy things in the trade I’m in. Definitely things I wouldn’t do myself or expect my team to do.
  18. E

    Wooden sticks

    This being my first hub motor or anything to do with this kind of thing it was just a general question Of “are they supped to be there?”. It’s good to find out about this stuff and what other people have to say.
  19. E

    Wooden sticks

    Ha ha. Not so much tech but more machinery and wood in 2020
  20. E

    Changing switch brake levers to magnetic hydraulic sensors

    Awesome. When the bike is up and running I’ll do it then. Definitely need a safety cut off to stop.
  21. E

    Hall sensor confusion

    Yeah. I’ve checked all the combinations that I’ve seen on the net. I’ve checked all the continuity on the main wires. I even reworded them and cut out where all the kinks were just incase they had breaks in
  22. E

    Wooden sticks

    Yup very true. Well this is my first hub and everything is a learning curve. If it goes badly wrong I can upgrade to something better
  23. E

    Wooden sticks

    Yeah does seem bad but I’m guessing they wouldn’t have someone opening them up. If they are ok being there and safe that’s fine
  24. E

    Changing switch brake levers to magnetic hydraulic sensors

    Hi guys. Working my way through conversation kit and the search function. The levers that came with the kit have switch sensors and I want to change the to the magnet sensors. Is it a case of wiring in the new cable and both would work in the same way?
  25. E

    Wooden sticks

    When I first took it apart and saw them it did make me think how you have all this tech and a primitive stick
Back
Top