ebike11 said:The 178mm bottom bracket from cyclone is offset
Does the longer end go on the crank or noncrank side? Thx
Left side, to clear the rear end of motor.
ebike11 said:The 178mm bottom bracket from cyclone is offset
Does the longer end go on the crank or noncrank side? Thx
Skaiwerd said:Does this go here?
Referring to the above post
ebike11 said:Sorry had another quick question.
What is the name or model of the tool needed to tighten the cyclone lockrings? Cyclone said they dont have it available. I mainly see just BB tools for the shell itself not the lockrings
Thx
Those two 10mm spacers you have there in the right blue bowl.markz said:Anyone know what the spacer width is on the drive side?
markz said:Same ole problem for me.
I will try a helicoil.
pedal.jpg
joshuahuang said:Anyone know how to fix the throttle? I have the stock non bluetooth 40a controller and the throttle response is terrible because it's speed controlled not current controlled. Do I need a new throttle or is there another solution? It's manageable on road but not for steeper technical trails.
joshuahuang said:Anyone know how to fix the throttle? I have the stock non bluetooth 40a controller and the throttle response is terrible because it's speed controlled not current controlled. Do I need a new throttle or is there another solution? It's manageable on road but not for steeper technical trails.
robocam said:Or you could replace the arms.
https://lunacycle.com/parts/cyclone-parts/standard-square-tapered-crank-set-for-cyclone-pair/
http://sickbikeparts.com/cranks-170mm-freewheel-crank-set/
http://sickbikeparts.com/cranks-175mm-freewheel-crank-set/
http://sickbikeparts.com/cranks-152mm-freewheel-crank-set/
robocam said:What throttle are you using? Maybe give it some time to get used to?
nah I've had it for a couple months now. I had no trouble adjusting to other throttles. It jerks really hard on startup no matter how slow i go
woah i didn't know stock one had bluetooth. ill see if i have the plug on the controller when i get homeTommm said:joshuahuang said:Anyone know how to fix the throttle? I have the stock non bluetooth 40a controller and the throttle response is terrible because it's speed controlled not current controlled. Do I need a new throttle or is there another solution? It's manageable on road but not for steeper technical trails.
If you have the leads for the bluetooth module you can buy one on ali for $20.
https://m.aliexpress.com/item/32...4569amp-img_XjHNYH_9K1acmgc8hA1570911340635
Or you can try to connect/disconnect the "soft start" leads. They are two grey wires and they plug into each other.
Tbh only way I got it just right was "fast start 8, adjust accelerator curve on" and a top of the line domino throttle ($70).
endrew said:Couple of questions regarding controllers:
1) Is there a good current based alternative to stock controller? stock controller controls speed rather than current.
2) When I try to set overspeed in stock controller, I can only set it up to 15. If I try to set it higher, It goes down to 15 after I hit "save". Why is that?
3) What is "low speed ratio"?
Thanks!
Nucular.endrew said:1) Is there a good current based alternative to stock controller? stock controller controls speed rather than current.
endrew said:Couple of questions regarding controllers:
1) Is there a good current based alternative to stock controller? stock controller controls speed rather than current.
2) When I try to set overspeed in stock controller, I can only set it up to 15. If I try to set it higher, It goes down to 15 after I hit "save". Why is that?
3) What is "low speed ratio"?
Thanks!
minimum said:Nucular.endrew said:1) Is there a good current based alternative to stock controller? stock controller controls speed rather than current.
12F if you're bold and do like changing your bicycle drivetrain components.
6F is good enough to destroy weaker links and get maintenance cycle low![]()
robocam said:What controller is this? Would you happen to have a link? What software is this screenshot from?
endrew said:Couple of questions regarding controllers:
1) Is there a good current based alternative to stock controller? stock controller controls speed rather than current.
2) When I try to set overspeed in stock controller, I can only set it up to 15. If I try to set it higher, It goes down to 15 after I hit "save". Why is that?
3) What is "low speed ratio"?
Thanks!
endrew said:Do you have experience pairing it with the cyclone?
Thanks!Tommm said:endrew said:Couple of questions regarding controllers:
1) Is there a good current based alternative to stock controller? stock controller controls speed rather than current.
2) When I try to set overspeed in stock controller, I can only set it up to 15. If I try to set it higher, It goes down to 15 after I hit "save". Why is that?
3) What is "low speed ratio"?
Thanks!
This menu sets the speed of the "high speed mode" and "low speed mode" of the 3 speed switch. If you are in the middle speed(default state without a 3 speed switch connected), it doesn't change anything. It doesn't change max power, it is just an rpm limit. The high speed mode is just field weakening.
15% is a lot, on 72v with the 15% setting you can run into the controller's rpm limit and experience some skipping, mostly without a load.
Reguarding the throttle, the best usability is with the "adjust accelerator curve" turned on. Slow start off, and fast start on 6 to 8 depending on taste.