Recent content by heynow9991

mid drive motor made by Lightning Rods https://lightning-rods10.mybigcommerce.com/single-stage-big-block-middrive-rhd/ It is built on a Klien Frame. It has a Cycle Anylyst digital dashboard. All the parts are top of the line Peter pmistel@gmail.com $1500 CAD

Hi I bought a Davinci Drive several years ago from the classifed section on this website. I tried mounting it in a bike but I could never get it setup properly so I gave up. I have been looking for a use for it so this is what I have come up with. I invite people to look at what I am doing...

I bought 6 of these packs. shipping was pretty quick and they shipped to me using the shipper of my choice, which is important when shipping to canada. I promptly ripped one pack open to do a quick and dirty check of capacity and got over 3000mah. might get more per cell, the test was rushed...

HI, I sent you a PM, Thanks

On th Motocruzin website it shows they have the Pro in stock. My problem is I am in Canada, but near to Buffalo. For large shipments I usually ship to a UPS store in NY state and go and pick it up as shipping is killer for large or expensive packages to Canada. The border is closed until June...

I didn't know you can still buy motopeds. They have the Pro version in stock. Question for LR, if I were to buy the Pro version, can you sell me a kit with the motor and whatever other parts are needed to complete the driveline? Battery I can take care of myself but I would look to you for a...

I will try to rebuild the hubmotor, so I ordered some new hall sensors and wire from ebike.ca. This is the controller I have, does anyone know the specs? I tried googling the serial numbers but I get nothing. Agin it is probably 10 years old. Lets hope it still works. It has been sitting on...

Thanks for the advice Questions about a sensorless controller, right now I have a Lyen controller that came with the motor, I will get the model number, but can I use it without the sensors? Will it work if I just leave the sensors unpluggged? I googled a bit and it seems it is a HT35 series...

I have an old ebike I am trying to fix. It has this Crystalyte hub motor on it. I cant get it to work so I took it apart and it looks like the wires going into the hub are damaged. I also measured the voltage to the hall sensors with the controller powered up, and I would get 5 volts...

I have this Tesla module that has been reconfigured so that it is 12S37P. I need to add another string to it as I need more voltage for the boat motor I want to power. I had a 12s BMS but I need a 13s bms for the new configuration. I expect to draw as much as 100 amps powering the motor. Any...

HI, I have some questions about an older Stealth fighter. I am considering buying a Stealth fighter with no battery. I believe it was number 56? Can anyone point me to where I can find the specs for battery compartment size , how many volts the controller can take etc. My plan would be to...

Thank you Matt, I responded to it.

I have a davinci drive with an astro 3220 with a half inch shaft. I was going to use the motor in a different application and I ended up destroying the pulley on the motor taking it off. I now want to use the complete drive again so I need to get that pulley replaced. Does anyone know how to...

I just bought a Briggs and Stratton 3 hp electric outboard on ebay. It is about 10 years old and has an Etek motor and Sevcon Millipak controller. It is 48v x 3hp = 2223 watts/48v = 46 amps. Lets call it 50 amps. I have several batteries, and I am trying to figure out what would be the best...

Hi I just bought a Briggs and Stratton Etek outboard on eBay. I don't have it yet but I want to get a head start on how I might power it. I have searched the internet for a manual but can't find anything. All I know is that it is 48v and draws about 80amps at full power. I assume it was...