Recent content by rogerc

Is he going to get arrested for taking a drink from the faucet on school grounds too? This is ridiculous and if the police have this much time on their hands I got a few neighborhood that they can hang out in. Waste of tax payers money to pursue this and over use of the court system. A judge is...

I am most concerned about not being able to pull more than 19 amps and only 1750 watts as shown by the cycle analyst 3. Any suggestions? RC

Nope only get about 1750 watts max on my set up. What settings do I need to change to get 2100 watts and over 30 amps? RC

I have a Mac 10 t set up from cellman with the 9 fet 3077, 36-50V Infineon Controller and the Cycle Analyst 3 with the 50 v 18.5 ah battery. My top speed is just under 24 mph and I thought it would be just a tad higher. Also the diagnostic screen will show the A (amp) limit flag when I first...

I got the same kit and put it together during the last 2 weeks, riding it now and it is great. Take your time, I am just barely an average mechanic and got it together with trial and error and patience. First you should look at this link it is a picture of all the wiring hook ups supplied by...

Have a Cellman mac 10 kit with a Cycle Analyst 3 and infenion controller. Is it possible to program the 3 way switch with the CA 3 to different settings say 750, 1250 and 1750? If so how do I accomplish this? Also is there a way to program the abruptness out of the throttle upon start up? I am...

Spent about an hour going over everything and checking and rechecking. Could not find anything wrong, nothing rubbing, wheel was trued and spokes checked. Zilch, zero, nada. Decided to check the screws that hold on the covers to the motor. Well guess what, a few were just slightly loose, tighten...

Trying to isolate the sound it appears to be coming from the freewheel. I got it from em3, (cellman). I may order a new one to and put in on and see if that helps. Can I just ignore the freewheel noise? Freewheel probably really hard to get off. It is there under power if I am not pedaling, and...

No not that noise.... While riding I am hearing a loud click coming from the rear, not sure if it is the motor, derailleur, brakes or exactly where. It increases as the speed increases and is a clear pattern. When I start pedaling it disappears and all is quiet. This is a Mac 10t motor brand...

Okay here goes, have to ask this even though I think I know the answer and will get some dumb looks from you guru's. I purchased a version 4 torque arm Grim Tech and due to a rear rack installed on the bike it does not fit and I need the rack for my bike design. Is it mandatory that the torque...

Always impressed with the knowledge on this board. I learn something everyday. I must have skipped school when they were teaching about electricity ( i really did cut high school a lot, always went to my college classes) and never got an understanding until I starting reading at this forum...

Ok.... I'll keep it below 95 C. Thanks for the replies. I assume the temp sensor with the CA 3 is pretty accurate and coming right from the internals of the motor. Surprised that these hills heated it up so quickly. Will have to see if I need to lower my amps. RC

Got my kit installed test rode it and watched the temperature on the Cycle Analayst 3.0 and most of the time around 50 C. Did some steep hill climbing and it got up to 90 C. What is too hot for a Mac 10 T motor? RC

First nice ride! Second that bag looks perfect. Adds some cushioning, is out in the air, and a place for the wires!! Will probably go that way soon. Thanks everyone for the replies, as usual a good solution was obtained from this forum. Actually I had given up on that bag thinking it was just...

I am installing the same kit right now. Having some small problems with build but should be figured out in a day or two. rode it just up and down the street and wow can't wait to sort everything out and start enjoying this puppy. So far very happy with the kit quality. Will write up a full kit...