Search results

Date Relevance Most replies

  1. H

    Motor not running, very small torque

    Had this problem turns out that the three wires to the motor were hooked up wrong.
  2. H

    a2b scooters problem

    Still no word, and now the phone number takes me to Go mobility Scooters who say I have the wrong company. Research shows that Jeff Cooperman runs both a2b and Go Mobility Check out the two websites http://www.gomobilityscooters.com and http://a2bscooters.com note they both list the same phone...
  3. H

    a2b scooters problem

    They haven't said anything and the statious of my order on there tracking page remains blank.
  4. H

    a2b scooters problem

    I have ordered a Lashout bike rack from a2b scooters http://store.a2bscooters.com/ ten days ago and after numeriouse attempts to call them (always goes streight to voice mail) and e-mail them. I have not heard anything and have been unable to get a hold of anybody. I am starting to get very...
  5. H

    Battery from battery which is also getting battery

    Well I lack the know how to split a ping battery and unfortunately for me everyone who does know how is probably in San Fransisco (I'm in Massachusetts). Also the rack cost over $50 and I was quoted almost as much to weld it back together as it would cost for a new rack. The bike rides fine even...
  6. H

    Battery from battery which is also getting battery

    So I just got my hub motor set up to elivate all the problems I had with the old side mounted motor when something else came up. My bike rack has finely had it and the welds have failed in many places. Well my set up was this a marine battery case with bubble wrap, and other soft things to...
  7. H

    To much power draw?

    I upgraded my bike to a hub-motor and have noticed a sigfentely higher wattage draw than my old set up. This new set up I have seen draw up to 1,900 Watts and I am worried that might be to much for my battery. I have a Ping 48V 20AH V2.5 LiFePO4 Battery Pack and it says recommended for motors of...
  8. H

    Help with HS3540

    Thanks for all your help I swaped the wires in the way Linn sujusted it still diden't work. I could have made a mistake in wire matching since one strand of wires was black and I had to trace them back to the plug each time to match color. Any way I just happened to switch two hall wires and it...
  9. H

    Help with HS3540

    Uh no it does not work fine.
  10. H

    Help with HS3540

    Hooked up and under powered more problems see the video I posted here http://www.youtube.com/watch?v=hpclZZwXrUk Specs Crystalyte Motor Style:HT3525 - torque motor (REAR) 12 FET 3077 Mark II Extreme Modder LYEN Edition Controller Rev4 torque arm Ping 48v 20AH LiFePO battery Phase wiring...
  11. H

    Help with HS3540

    I never liked bullett conectors because they weren't as secure as other connectors, but if they are better maybe I should. It is hard for me to tell the wireing color comming from the motor though because it is all covered up.
  12. H

    Help with HS3540

    My controller is a 12 FET 3077 Mark II Extreme Modder LYEN Edition Controller I just got the motor and here are my hook ups A 5 pin hook up of some sort for the hall sensor (and I have no idea what wire corresponds to what) And a three pronged plug for the power. Does anyone know where to get...
  13. H

    2013 Electrical Systems-Close Call & Lessons Learned Thread

    To keep the cables from torching I cut one shorter then the other. So if I had a battery one lead would be 4 inches long with .5 inch of conductor exposed and the other will be eight inches with .5 inches of conductor exposed so in order for them to touch you would physically bend the longer...
  14. H

    Help with HS3540

    I think can rearrange the three power wires until I have the right combination, but doing so on the hall sensor will be difficult. How will I know which wire goes where on the hall sensor pickup?
  15. H

    Help with HS3540

    BUMP Because I know someone on here must have a HS3540.
  16. H

    Help with HS3540

    :?: I am upgrading to a HS3540 rear mounted hub-motor and would like to know what wiring work I need to do to the controller to make it all hook up right. These are the plugs that currently come from the controller a six pin female (for what I assume is the hall sensor) and three individual...
  17. H

    Cree LED Chrome Bullet Headlight?

    Get the head light in the pic you posted and mod it into an LED light.
  18. H

    HELP! I am sick of dealing with my Lashout

    The only modification that has recently been done was inserting a cut Allen wrench into the elongated motor plate to hold it in place (read more about it here http://endless-sphere.com/forums/viewtopic.php?f=3&t=38748) I really want to get this problem solved before I blow $180 on replacement...
  19. H

    MAC-BMC Motor, planetary gearbox efficiency study

    I am using the EVDeals/Scott McGregor version, the spare gear set up was from the older gear box (the gear assembly looks the same though). It's haveing them go one right after the other that has me puzzled). You can get more Planetary Gear Assembles here...
  20. H

    MAC-BMC Motor, planetary gearbox efficiency study

    I have been running 1,000 watts at 48 volts through these and recentely after a few years of use the sun gear broke. Now I had another planetary gear set and put that in and just about a mile into my ride the sun gear on that one broke. The first time I wrote it off as wear and tear but haveing...
  21. H

    NO WASTE HEAT OR COOLING NEEDED...

    So I was at the detest and picked up Smithsonian magazine and found an article on electric trucks http://www.smithsonianmag.com/science-nature/Forget-the-Volt-Make-Way-for-Electric-Trucks-169807746.html what got me was this "Here is Hansel’s pitch, in a nutshell: Electric motors are powerful...
  22. H

    Need help picking a hub moter

    I want one that works and has the same torque and speed my current setup has. my setup can push 30mph and is geared 13.6:1. I need the hill climbing ability.
  23. H

    Need help picking a hub moter

    Sun gear broke on my Modified Lashout (1,000 watt motor/ 48v 20AH Ping/ 12 FET 4110 Mark II Extreme Modder LYEN Edition Controller) So I am going to get a hub motor because I am sick of always having problems with the current setup. I am wondering what recommendations there are for 1,000+ Motors...
  24. H

    HELP! I am sick of dealing with my Lashout

    Yes I plan to use the current frame.
  25. H

    HELP! I am sick of dealing with my Lashout

    Sun gear broke on my Modified Lashout (1,000 watt motor/ 48v 20AH Ping/ 12 FET 4110 Mark II Extreme Modder LYEN Edition Controller) I have been riding it like this for awhile so I thought it just wore out so I put in another planetary gearing assembly that I had laying around and took off. No...
Back
Top