Search results

Date Relevance Most replies

  1. ecologymagnet

    ME0913 from Zero bike 2012 in buggy and minimum controller?

    My question is if the controller will be sufficient temporarily for that motor, since to test my idea is to use a 15 Fets of up to 84V and 45A. Thank you!
  2. ecologymagnet

    ME0913 from Zero bike 2012 in buggy and minimum controller?

    Any idea?
  3. ecologymagnet

    ME0913 from Zero bike 2012 in buggy and minimum controller?

    I want to convert my 150cc and 400 lbs buggy to electric, I have done quite a few conversions from bikes and mini bikes; but this is the heaviest and doubts arise. I have a "Moto Energy 0913 from Zero 2012 bike" engine that I want to power with 18S Nanotech 8Ah 25 / 50C; but I doubt if they...
  4. ecologymagnet

    Which Kelly Controller model is this?

    It looks like a KBS, the mini version of a Kelly controller, will it be too small for the engine I indicate above, a ME0913?
  5. ecologymagnet

    Which Kelly Controller model is this?

    No, I don´t have the dimensions.
  6. ecologymagnet

    Which Kelly Controller model is this?

    One seller sell me a Kelly Controller model that tell me supports 120V and 200A; but they don't know what model it is for losing the sticker, I have pictures of him, what model could it be? Will it power a Zero Motorcycles ME 0913 engine or will the controller burn out? For this motor:
  7. ecologymagnet

    1 Throttle and 2 Controller with Regen

    Any idea?
  8. ecologymagnet

    1 Throttle and 2 Controller with Regen

    I want to connect two controllers to a single battery and a single accelerator. I understand that one of the controllers I only have to connect the signal cable of the accelerator and not connect the positive and the negative. In the case of regeneration with a single button, how should I proceed?
  9. ecologymagnet

    MXUS 3000 @ 24S and 30S LIPO 80A

    I have tested my MXUS 3000 at 24S Lipo Nanotech 8000 and a Leo controller up to 80A and I have been very satisfied with a lot of acceleration and 80 Kms/h on level and 90 with lowering. Now I think about putting 30S with 80A, which I think the Leo controller supports, will it support the motor...
  10. ecologymagnet

    Alternator coverted to Brushless Motor

    I am passing an alternator to a brushless motor; but I have a series of problems: 1) Flashing when starting, I think I should put sensors, any ideas for it? 2) I doubt about the voltage of the internal rotor, I tried with 6v and 12v, recommend in some guides 5v and if it seems to work well to...
  11. ecologymagnet

    MXUS 3000 @ 24S and 30S LIPO 80A

    I need a bms for 24s Lipo and peak 80A. I also do not rule out buying a charger or charging them disconnected with my icharger. The use is a battery for an ebike with a MXUS 3000 and a modified alternator in a Quad, both with a maximum controller 80A. I have no screen in either of the two, so...
  12. ecologymagnet

    Center printed pulley?

    How can I center a printed pulley in a normal wheel? Thank you.
  13. ecologymagnet

    ¿Sensored or Sensorless?

    I am thinking on buy this motor for a Xerun 150A with sensored and 6S Nanotech 8000 25/50: http://www.ebay.com/itm/5065-50-65-270KV-Heavy-duty-brushless-Sensored-motor-2-6KG-3-8S-for-Skateboard-/181913685694?hash=item2a5ae68ebe:g:iVIAAOSwnNBXVs7f But I don´t know the brand.
  14. ecologymagnet

    ¿Sensored or Sensorless?

    Wich is the pros and cons of sensored motor? I go build a 6S single motor with a Xerun 150A with Sensor port. And wich is the best brand or model?, Turnigy, NTM, Aeolian, Tacon... Thank you very much.
  15. ecologymagnet

    Motor for E-longboard on Hobbyking

    I want to built an E-Longboard; but I see that all the engines that I know are out of stock in HK, There is some motor in stock that I can use in the store in China or Europe? And in other web?
  16. ecologymagnet

    Speedict Ebike - Anybody seen/tried this?

    Is it possible to fix a Speedict out of warranty? What would it cost?
  17. ecologymagnet

    Speedict Ebike - Anybody seen/tried this?

    Today I connected my Speedict as always with my battery 18S (4,15V per cell); but it has seen sparks in the Speedict and this no longer works, how I could repair it? I am interested in this because I would not mind paying 15 €
  18. ecologymagnet

    Power Suplly 12V for 18S @ 10A

    I charge 3 batteries 6S@10A each and I'm thinking to buy a computer power supply for the 3rd charger or if there is any economic source power that can feed the 3 chargers at once. Now I have a Turnigy 350W and Power Suplly 400W for two chargers, I need other power suplly or one power supply...
  19. ecologymagnet

    Speedict Ebike - Anybody seen/tried this?

    Perfect, I will not use the regen.
  20. ecologymagnet

    Speedict Ebike - Anybody seen/tried this?

    Is safe use Speedict with 18S and regen? I think that with the regeneration exceed 80V.
  21. ecologymagnet

    MXUS 3000 Hub Motor - V1 V2 V3

    Leo confirms me that the Greentime 24 with fets 4115 supports 130V, I will try 30S, I could usually go in mode 2 with up to 45A and 80A temporarily. Surely I will gain efficiency and autonomy to carry more batteries, I guess that the axle will support. I use now speedict, is there more...
  22. ecologymagnet

    MXUS 3000 Hub Motor - V1 V2 V3

    Any idea? Thank you!
  23. ecologymagnet

    MXUS 3000 Hub Motor - V1 V2 V3

    I doubt if convert my mxus 3000 from 18S 80A to 30S 80A. (Nanotech 8000 25/50C) My controller is a 24 Fets 4115 Greentime Pros and cons?
  24. ecologymagnet

    Greentime controllers

    I tested my 24 Fets controller with Mxus 3000, the 3rd speed only activate with connected sensors, on 3rd speed makes a noise every lap and vibrate. On 3rd speed the motor spin more fast. Any ideas?
  25. ecologymagnet

    Greentime controllers

    Yes, I use Nanotech 8Ah . The controller under hard use is very cool on hot days . Thank you very much for your help.
Back
Top