Erikjan said:Is it posible to get a manual with a white background?
Tis looks good but coast much ink when i print it.
yes i can remove the background, oh i just realized our users will print it out !
Erikjan said:Is it posible to get a manual with a white background?
Tis looks good but coast much ink when i print it.
Erikjan said:will read it tomorrow. Hope the divice arrive soon.
Erikjan said:Is it posible to get a manual with a white background?
Tis looks good but coast much ink when i print it.
Velcro01 said:Hi Danny,
I have a problem with the PC Suite v1.06
I am using WinXP and have succesfully installed the USB Driver. The Speedict USB Device shows up in the device manager when connected and windows says it if functioning correctly, however the PC suite does not see the device...
Any ideas?
Thanks.
Cheers, Martin.
Velcro01 said:Thanks for the reply Danny,
You are right. This is Mercury. I only just noticed the "Mercury" on the side. I wrongly assumed tghat I had the ebike.
This is meant for BOSCH systems, isn't it? I am trying to install it on a Cyclone DIY kit. Will it be suitable?
Cheers, Martin.
speedict said:cwah said:Congratulation for your new product MERCURY. I've seen it's limited to 70V?? Damn, you're going to miss a lot of customers in endlessspehre. Why not increase the max voltage? The Cycle analyst has a good limit of 150V and that's nice.
hi cwah,
don't mix up, this is (mercury) for bosch system, not for DIY market
Velcro01 said:Hi Danny,
an earlier post made me think that Mercury was anly for Bosh E-Bike systems..
speedict said:cwah said:Congratulation for your new product MERCURY. I've seen it's limited to 70V?? Damn, you're going to miss a lot of customers in endlessspehre. Why not increase the max voltage? The Cycle analyst has a good limit of 150V and that's nice.
hi cwah,
don't mix up, this is (mercury) for bosch system, not for DIY market
I was/am a little confused..
So this (Mercury) is OK for my DIY Cyclone e-bike?
Thanks again.
Cheers, Martin.
Velcro01 said:Hi Danny,
an earlier post made me think that Mercury was anly for Bosh E-Bike systems..
speedict said:cwah said:Congratulation for your new product MERCURY. I've seen it's limited to 70V?? Damn, you're going to miss a lot of customers in endlessspehre. Why not increase the max voltage? The Cycle analyst has a good limit of 150V and that's nice.
hi cwah,
don't mix up, this is (mercury) for bosch system, not for DIY market
I was/am a little confused..
So this (Mercury) is OK for my DIY Cyclone e-bike?
Thanks again.
Cheers, Martin.
Velcro01 said:
lol looks like they increased camera speed for the people going up the stairs. going that fast the ladies hair would have been flopping in the wind. pretty cheesyVelcro01 said:
Yeah. You are right, it does look cheesy :lol:atcspaul said:lol looks like they increased camera speed for the people going up the stairs. going that fast the ladies hair would have been flopping in the wind. pretty cheesy
DeepSouth said:Hi Danny Very impressive product am going to order one of these myself. Can't wait till you release a full controller.
I have very similar questions to advancedo's post above. I have read the entire thread with a great deal of interest. But am still uncertian as to the differences between Mercury, Venus and Mars.
Which one should I purchase. I have a 48V GNG 1000W Mid drive Mountain bike which is awesome, but the throttle is very twitchy in the bottom gears. I was hopping that I would be able to use Speedicts throttle control to even that out.
Keep up the Good work.
speedict Wrote:
can i have more information about GNG mid drive system ?