terr513
10 mW
- Joined
- Jun 24, 2012
- Messages
- 30
Hello all,
Thank you again for all your interest, time and posts.
Bike is moving, I think at correct speed, all I have to compare it to is a little jap scooter I have, EVG goes much faster (duman- the throttle is new replaced when trying to diagnose this gear problem) but I'm getting a high pitched sound from rear. This may be my brakes as there way out of whack rear not releasing, I keep trying to adjust them but I suck at it, also I messed up the NEW Derailleur getting the rear wheel off and I really suck at adjusting them so I need to get it to a bike shop to do that part.
But before I do any adjusting I am going to take the motor back off and look inside, it did seem to slip a bit, might have just been the roll pin flatting out but I would like to look. Yes I would feel more comfortable if there were 3 Pins but since BOB the Mechanic wont take any money from me I hate to ask him. He said he did not feel comfortable tack welding it because there is a rubber ring in there and he is worried about the heat.I'll know more when I get the motor back off. Icewrench - I think that gear only spun one way after he pinned it, but I will check when I get it off.
I also busted the Control piece that runs the light,horn,criuse,econamey mode, now my light does not work, but I think snellemin has one he said he would sell me. I should have hung it from my garage ceiling like I usually do to work on it.
I also changed the seat post to make it lower, my feet were over a foot off the ground when I stop :lol:
Bad news for me is I brought the battery pack inside last night to charge it and put the Thermal Switch back in it, ( I took it out because I need to get a new one, kind of crustie) I was moving the battery pack from one table to another and pulled my elbow out,heavy SOB, so I'm working one armed today and it is already 89 degrees here in Cinci at 8:00 in the morn.
Thank you again for all your interest, time and posts.
Bike is moving, I think at correct speed, all I have to compare it to is a little jap scooter I have, EVG goes much faster (duman- the throttle is new replaced when trying to diagnose this gear problem) but I'm getting a high pitched sound from rear. This may be my brakes as there way out of whack rear not releasing, I keep trying to adjust them but I suck at it, also I messed up the NEW Derailleur getting the rear wheel off and I really suck at adjusting them so I need to get it to a bike shop to do that part.
But before I do any adjusting I am going to take the motor back off and look inside, it did seem to slip a bit, might have just been the roll pin flatting out but I would like to look. Yes I would feel more comfortable if there were 3 Pins but since BOB the Mechanic wont take any money from me I hate to ask him. He said he did not feel comfortable tack welding it because there is a rubber ring in there and he is worried about the heat.I'll know more when I get the motor back off. Icewrench - I think that gear only spun one way after he pinned it, but I will check when I get it off.
I also busted the Control piece that runs the light,horn,criuse,econamey mode, now my light does not work, but I think snellemin has one he said he would sell me. I should have hung it from my garage ceiling like I usually do to work on it.
I also changed the seat post to make it lower, my feet were over a foot off the ground when I stop :lol:
Bad news for me is I brought the battery pack inside last night to charge it and put the Thermal Switch back in it, ( I took it out because I need to get a new one, kind of crustie) I was moving the battery pack from one table to another and pulled my elbow out,heavy SOB, so I'm working one armed today and it is already 89 degrees here in Cinci at 8:00 in the morn.