Search results

Date Relevance Most replies

  1. D

    Methtek HVC/LVC working

    I want to make sure my current setup is working properly. Above methods recommends to send boards back to him for testing. At the moment that's not quite an option. Anyone have some advice on how to check each board, check throttle retard is operational, and of course HVC breaker. Thanks for...
  2. D

    Phasor/cro /meth24fet/fans/ca3/HVC LVC don't do what I do!!!

    Haven't posted in a bit but this is kind of connected to little bit of everything. Just like posted above. 2nd build, frocked up everything I could in first :D that's another story. So phasor-cycles.com frame, methods HVC/LVC [urlhttp://www.methtek.com/category/battery-protection/][/url]and...
  3. D

    High voltage controller key switch

    On a 100v setup with methods 24 fet. I want to swap controller on off button to key switch. Can I use any 125Ac switch, how many Amps should it be rated for as well. These are not main power lines just controller on off!! (Still showing pack voltage on multimeter) Would something like this...
  4. D

    Lipo sparks.... Help

    Putting together a 24S 4P of 8s 5.8Ah lipo packs. Separated packs into 3 separate 4 packs. The 8S packs have two separate 4S balance taps. So... What did I do wrong..... Grabbed 1st 4 packs. Took 1 4s tap out of each into one of methods LVC/HVC parallel boards. Started plugging in 2nd set of...
  5. D

    Unplugged HS3540 phase and.....

    Here's the pics Hadn't unplugged phase wires in months or even seen them since they are covered. Got a flat 2 days ago. Took tire of yesterday phase plugs are partially melted. Glad to have caught this now. I use 18S lipo with 40A crystalyte controller like ebikes ca sells. I do push this...
  6. D

    Schlumpf high speed drive group buy???

    First of everything you need to know about Schlumpf drives here. http://www.schlumpf.ch/hp/schlumpf/faq.getriebe.engl.htm Been looking into Schlumpf drives, and others, hammerschmidt, Patterson, ats for use on my next build. My only problem is all of the above are not compatible with phasor...
  7. D

    Crystalyte 4065?? Who has some info?? Or...? On phasor frame

    Looking to get an off road ebike frame probobally phasor cycles. My plan is to run 24s4p (100.8v) with 18 fet Lyen at 80amps++ on 24inch wheels. Pretty fail safe motor option would be cromotor or 5403. My only issue with this is so much added weight! My current setup is running 18s4p air...
  8. D

    HS3540 hub open few questions

    Good news first, all halls working!! I was having an intermitent problem with one of halls. Lyen tester was only showing 3 halls when motor was freshly used, warm. Been using sensorless controller past few weeks. One of zip ties was way to tight so i cut it gave a bit of slack to wires and put a...
  9. D

    Lipo fully charged?

    Hey guys, when balancing lipo pack with battery medics I've read and seen on hyenas you tube video that pack should be fully charged before commencing. What's the reason? Also how crucial is this? The reason I'm asking is cause it takes so damn long to discharge to 4.10V on my 18S 4P when fully...
  10. D

    2nd try Help needed HS3540 to Lyen 12 fet

    Hey guys having some trouble getting this going..... I tried color combo recommended on Lyen instructions (also said to be right for most on es) for hall and phase... Controller > Motor HALL Red > Red Black > Black Yellow > Yellow Green > Blue Blue > Green PHASE Yellow > Blue Green > Green...
  11. D

    Motor/controller techs

    Hey guys, I was wondering if there was anyone on endless sphere that does mods on controllers and hub motors for a fee. If its someone in the south Florida area even better!! Thanks Fred
  12. D

    Its open, Lyen controller. Advice needed

    So I just wanted to extend some wires by soldering them together, existing 12 gauge for power and phase, and the smaller 23gauge for the hall wires. I ended up opening controller (not planned) and what do you know it doesn't seem to hard to just replace all the wires instead of extending and...
  13. D

    What type of wire to buy

    Hey guys, I have to extend some of my controller wires. I have a Lyen 12 fet. I have to extend some of the 23 gauge and some of the 12 gauge. Where should I buy and what type do you recommend? Thanks Fred
  14. D

    ebike torque arm placement

    Hey guys, I need to make sure I'm putting these torque arms on right! Not ideal I have to add extra nut for arm on axle, and the angle looks a bit iffy to me. What do you think? Will this work, I am going to be using two tourque arms. There will be quite a bit of power to setup, 18S4P with...
  15. D

    Security for ebike

    What do you guys think of these security solutions? Anyone try them? http://www.ebay.com/itm/Two-Way-Bicycle-Steal-Control-Anti-Theft-Alarm-Audible-Sound-Security-Lock-Bike-/170726436884?pt=LH_DefaultDomain_0&hash=item27c016b014#ht_3021wt_1102...
  16. D

    Lipo Bulk Charging

    Im building Lipo pack with 16x turnigy 6S 5Ah batterries http://www.hobbyking.com/hobbyking/store/__16207__Turnigy_5000mAh_6S_20C_Lipo_Pack_USA_Warehouse_.html for a 24S 4P 88V 20Ah I want to charge my whole pack at once here is the charging method I would like to use. 4 x HVC + LVC +...
  17. D

    trouble with the law?

    I was wondering if any of you have ever had any trouble with the law concerning your e-bikes, especially when driving over 20 mph. Im from south florida very urban area! Id appreciate some info, if you yourself have had problems with police (tickets,arrests?), or if you know anyone that has...
  18. D

    7240 phoenix 2 kit 2x 36v 15ah lithium manganese batteries

    Hey everyone, i am completely new to electric bikes. I need a bike to take me mostly to and from work. The thing is I live in south florida, and I work all over... My comute is anywhere from 5-35 miles. I also carry a lot of gear with me. I weigh 160lbs and sometimes an extra 40-60 lbs, ill be...
Back
Top