Search results

Date Relevance Most replies

  1. D

    I Feel Like A Noob Asking This Question!

    I have 3 MAC 8T motors, all on 12s4p lipo. All have EB3xx controllers set at the same battery amp and phase. I am trying to figure out why one is much faster than another. Fatser one has CST cyclops 26x2.4 other one Big Apples 26x2.35 tires. The one with the Cyclops has a EB306 controller the...
  2. D

    Half Twist throttle how do I adjust the off band?

    This is the second throtte that has changed the dead band. In order to stop I need to open the throttle about a 1/4". First one I thought was the heat that caused the HALL sensor to change. First time I thought it was the controller but during testing it turned out to be the throttle. I have...
  3. D

    8fun (bafang ?)

    You might get a little more speed by modding the controller shunt. But only if it's not enough power to get max rpm from the motor. Speed is increased mainly by voltage, so a higher amp controller will do little in speed. dan
  4. D

    Underlined Words? Are we being sold off for surveys?

    They lead to surveys or QuiBids? Are we being hacked or is this what we need to stay around. the bogus links scare me as we never know what you are really clicking on. Not all underlined words go off site, if I rt click open new page and i get something else. PING was underlined as I posted...
  5. D

    HEY ALL YOU MAC Drivers. What's The Limit?

    What do you think a 8 turn MAC will handle? 260lbs gross, 26" MTB, 15s4p Lipo, 12 fet Infinion irfb4110 fets. Max phase and current, block time? Running 100amp phase 65 current and 1.0 block time. Stock phase wires 6" into hub, 12ga up. At 120% throttle hard pedaling I can make just over...
  6. D

    X1, X2 - HELP I'm so confused!

    All right all you INFINION Guru's. How do I wire my 3 speed switch. I wired x1 x2 and ground. All I can get is shorting x1 and ground to change speed. It goes in steps using x1 never x2. What am I doing wrong. Keywin sent me a pinout for the EB3 boards and I think i have it wired as listed...
  7. D

    I have a technical question about this kit

    You will be able to run 48v with that setup, but not 24v as the controller will hit LVC and not run. the throttle will funtion but your battery level guage will not be any way near correct. As most aren't anyway. You should like the 128 hub and speed of 20mph on 36v without a problem. Are you...
  8. D

    CRYSTALYTE 406/4011 WHAT SHOULD I EXPECT?

    My cute hub took a vacation and won't be back to play. So in it's place I installed a 406/4011 rear hub with it's 36 to 72v 20a controller. I am running 48v 20a LiFePo4 pack. with the Cute hub with a 12 fet controller 28a I could get 30mph with assist and a great bottom end. Not as strong as my...
  9. D

    Anybody used the Cute motors yet?

    I was just wondering if anyone has done a fair test run on the Cite motor from BMSBATTERY yet. Just wondering what I would expect when i get to try mine. How do they compair to the Bafang and so.
  10. D

    EBIKERS IN THE CHICAGOLAND AREA

    i'm just wondering how many of us are in the Chicagoland area. Chicago is a very large city with many suburbs. So let yourself known to the rest of use in the area so we might be able to get togeater some time. Ride, BS or help each other. DAN
  11. D

    Is A 24v 500w & a 48v 1000w The Same on the Same Voltage?

    What determine the power of a hub motor? I have a 24v 500w rear hub and a 36v 500w also. I was asking if the 48v 1000w motor would run the same as the 24v 500w on the same voltage, say the 24 v run on 24v and the 48v on also 24v, what will be the results? Then the 24v & the 48v run on 36 and...
Back
Top